LCM of two numbers

Junction Voltage Calculator

Engineering Chemistry Financial Health More >>

↳

Electronics Chemical Engineering Civil Electrical More >>

⤿

Solid State Devices Amplifiers Analog Communications Analog Electronics More >>

⤿

SSD Junction Electrons and Holes Energy Band and Charge Carrier Semiconductor Carriers

✖Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points.ⓘ Source Voltage [V]			+10% -10%
✖Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction.ⓘ Series Resistance in P Junction [R_se(p)]			+10% -10%
✖Series Resistance in n Junction is defined as the total resistance in the series inside a circuit at n-junction.ⓘ Series Resistance in N Junction [R_se(n)]			+10% -10%
✖Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device.ⓘ Electric Current [I]			+10% -10%

✖Junction voltage is the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers.ⓘ Junction Voltage [V_j]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download SSD Junction Formulas PDF PDF Image

Junction Voltage Solution

STEP 0: Pre-Calculation Summary

Formula Used

Junction Voltage = Source Voltage-(Series Resistance in P Junction+Series Resistance in N Junction)*Electric Current
V_j = V-(R_se(p)+R_se(n))*I
This formula uses 5 Variables

Variables Used

Junction Voltage - (Measured in Volt) - Junction voltage is the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers.
Source Voltage - (Measured in Volt) - Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points.
Series Resistance in P Junction - (Measured in Ohm) - Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction.
Series Resistance in N Junction - (Measured in Ohm) - Series Resistance in n Junction is defined as the total resistance in the series inside a circuit at n-junction.
Electric Current - (Measured in Ampere) - Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device.

STEP 1: Convert Input(s) to Base Unit

Source Voltage: 120 Volt --> 120 Volt No Conversion Required
Series Resistance in P Junction: 23.3 Ohm --> 23.3 Ohm No Conversion Required
Series Resistance in N Junction: 476.7 Ohm --> 476.7 Ohm No Conversion Required
Electric Current: 0.2 Milliampere --> 0.0002 Ampere (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_j = V-(R_se(p)+R_se(n))*I --> 120-(23.3+476.7)*0.0002

Evaluating ... ...

V_j = 119.9

STEP 3: Convert Result to Output's Unit

119.9 Volt --> No Conversion Required

FINAL ANSWER

119.9 Volt <-- Junction Voltage

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics » Solid State Devices » SSD Junction » Junction Voltage

Credits

Created by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has created this Calculator and 900+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< SSD Junction Calculators

Junction Capacitance

LaTeX Go Junction Capacitance = (Junction Area/2)*sqrt((2*[Charge-e]*Constant Length Offset*Doping Concentration of Base)/(Source Voltage-Source Voltage 1))

Series Resistance in P-type

LaTeX Go Series Resistance in P Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in N Junction

Junction Voltage

LaTeX Go Junction Voltage = Source Voltage-(Series Resistance in P Junction+Series Resistance in N Junction)*Electric Current

N-Type Width

LaTeX Go Charge Penetration N-type = Total Acceptor Charge/(Junction Area*Acceptor Concentration*[Charge-e])

Junction Voltage Formula

LaTeX Go

Junction Voltage = Source Voltage-(Series Resistance in P Junction+Series Resistance in N Junction)*Electric Current
V_j = V-(R_se(p)+R_se(n))*I

What is the junction voltage of a semiconductor?

The p-n junction diodes made from silicon semiconductors works at high temperature than the germanium semiconductor diodes. Forward bias voltage for silicon semiconductor diode is approximately 0.7 volts whereas for germanium semiconductor diode is approximately 0.3 volts.

How to Calculate Junction Voltage?

Junction Voltage calculator uses Junction Voltage = Source Voltage-(Series Resistance in P Junction+Series Resistance in N Junction)*Electric Current to calculate the Junction Voltage, The Junction Voltage formula is defined as the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers. Junction Voltage is denoted by V_j symbol.

How to calculate Junction Voltage using this online calculator? To use this online calculator for Junction Voltage, enter Source Voltage (V), Series Resistance in P Junction (R_se(p)), Series Resistance in N Junction (R_se(n)) & Electric Current (I) and hit the calculate button. Here is how the Junction Voltage calculation can be explained with given input values -> 119.9 = 120-(23.3+476.7)*0.0002.

FAQ

What is Junction Voltage?

The Junction Voltage formula is defined as the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers and is represented as V_j = V-(R_se(p)+R_se(n))*I or Junction Voltage = Source Voltage-(Series Resistance in P Junction+Series Resistance in N Junction)*Electric Current. Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points, Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction, Series Resistance in n Junction is defined as the total resistance in the series inside a circuit at n-junction & Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device.

How to calculate Junction Voltage?

The Junction Voltage formula is defined as the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers is calculated using Junction Voltage = Source Voltage-(Series Resistance in P Junction+Series Resistance in N Junction)*Electric Current. To calculate Junction Voltage, you need Source Voltage (V), Series Resistance in P Junction (R_se(p)), Series Resistance in N Junction (R_se(n)) & Electric Current (I). With our tool, you need to enter the respective value for Source Voltage, Series Resistance in P Junction, Series Resistance in N Junction & Electric Current and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search