Initial Bolt Load to seat Gasket Joint Calculator

✖Width of u-collar in Gasket is definied as the measurement or extent of u-collar from side to side.ⓘ Width of u-collar in Gasket [b_g]			+10% -10%
✖Gasket Diameter is a straight line passing from side to side through the centre of a gasket.ⓘ Gasket Diameter [G]			+10% -10%
✖Gasket Unit Seating Load is the seating load on per unit area o the sealing gasket.ⓘ Gasket Unit Seating Load [y_sl]			+10% -10%

✖Initial bolt load to seat the gasket joint contact surface is defined as load in terms of either a concentrated force or a prescribed change in length.ⓘ Initial Bolt Load to seat Gasket Joint [W_m2]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Bolt Loads in Gasket Joints Formulas PDF PDF Image

Initial Bolt Load to seat Gasket Joint Solution

STEP 0: Pre-Calculation Summary

Formula Used

Initial Bolt Load to Seat the Gasket Joint = pi*Width of u-collar in Gasket*Gasket Diameter*Gasket Unit Seating Load
W_m2 = pi*b_g*G*y_sl
This formula uses 1 Constants, 4 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Initial Bolt Load to Seat the Gasket Joint - (Measured in Newton) - Initial bolt load to seat the gasket joint contact surface is defined as load in terms of either a concentrated force or a prescribed change in length.
Width of u-collar in Gasket - (Measured in Meter) - Width of u-collar in Gasket is definied as the measurement or extent of u-collar from side to side.
Gasket Diameter - (Measured in Meter) - Gasket Diameter is a straight line passing from side to side through the centre of a gasket.
Gasket Unit Seating Load - (Measured in Pascal) - Gasket Unit Seating Load is the seating load on per unit area o the sealing gasket.

STEP 1: Convert Input(s) to Base Unit

Width of u-collar in Gasket: 4.21 Millimeter --> 0.00421 Meter (Check conversion here)
Gasket Diameter: 32 Millimeter --> 0.032 Meter (Check conversion here)
Gasket Unit Seating Load: 3.85 Newton per Square Millimeter --> 3850000 Pascal (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

W_m2 = pi*b_g*G*y_sl --> pi*0.00421*0.032*3850000

Evaluating ... ...

W_m2 = 1629.45614482273

STEP 3: Convert Result to Output's Unit

1629.45614482273 Newton --> No Conversion Required

FINAL ANSWER

1629.45614482273 ≈ 1629.456 Newton <-- Initial Bolt Load to Seat the Gasket Joint

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Design of Machine Elements » Design of Coupling » Packing » Mechanical » Bolt Loads in Gasket Joints » Initial Bolt Load to seat Gasket Joint

Credits

Created by sanjay shiva

national institute of technology hamirpur (NITH ), hamirpur , himachal pradesh

sanjay shiva has created this Calculator and 100+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Bolt Loads in Gasket Joints Calculators

Bolt Load under operating condition given Hydrostatic End Force

LaTeX Go Bolt Load Under Operating Condition for Gasket = ((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)+(2*Width of u-collar in Gasket*pi*Gasket Diameter*Pressure at Outer Diameter of Gasket*Gasket Factor)

Hydrostatic End Force given Bolt Load under Operating condition

LaTeX Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-(2*Width of u-collar in Gasket*pi*Gasket Diameter*Gasket Factor*Pressure at Outer Diameter of Gasket)

Bolt load under operating condition

LaTeX Go Bolt Load Under Operating Condition for Gasket = Hydrostatic End Force in Gasket Seal+Total Joint Surface Compression Load

Hydrostatic end force

LaTeX Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-Total Joint Surface Compression Load

Initial Bolt Load to seat Gasket Joint Formula

LaTeX Go

Initial Bolt Load to Seat the Gasket Joint = pi*Width of u-collar in Gasket*Gasket Diameter*Gasket Unit Seating Load
W_m2 = pi*b_g*G*y_sl

What is Bolt load?

Bolt load is defined as load in terms of either a concentrated force or a prescribed change in length.

How to Calculate Initial Bolt Load to seat Gasket Joint?

Initial Bolt Load to seat Gasket Joint calculator uses Initial Bolt Load to Seat the Gasket Joint = pi*Width of u-collar in Gasket*Gasket Diameter*Gasket Unit Seating Load to calculate the Initial Bolt Load to Seat the Gasket Joint, The Initial Bolt Load to seat Gasket Joint contact surface formula is defined as load in terms of either a concentrated force or a prescribed change in length. Initial Bolt Load to Seat the Gasket Joint is denoted by W_m2 symbol.

How to calculate Initial Bolt Load to seat Gasket Joint using this online calculator? To use this online calculator for Initial Bolt Load to seat Gasket Joint, enter Width of u-collar in Gasket (b_g), Gasket Diameter (G) & Gasket Unit Seating Load (y_sl) and hit the calculate button. Here is how the Initial Bolt Load to seat Gasket Joint calculation can be explained with given input values -> 1625.586 = pi*0.00421*0.032*3850000.

FAQ

What is Initial Bolt Load to seat Gasket Joint?

The Initial Bolt Load to seat Gasket Joint contact surface formula is defined as load in terms of either a concentrated force or a prescribed change in length and is represented as W_m2 = pi*b_g*G*y_sl or Initial Bolt Load to Seat the Gasket Joint = pi*Width of u-collar in Gasket*Gasket Diameter*Gasket Unit Seating Load. Width of u-collar in Gasket is definied as the measurement or extent of u-collar from side to side, Gasket Diameter is a straight line passing from side to side through the centre of a gasket & Gasket Unit Seating Load is the seating load on per unit area o the sealing gasket.

How to calculate Initial Bolt Load to seat Gasket Joint?

The Initial Bolt Load to seat Gasket Joint contact surface formula is defined as load in terms of either a concentrated force or a prescribed change in length is calculated using Initial Bolt Load to Seat the Gasket Joint = pi*Width of u-collar in Gasket*Gasket Diameter*Gasket Unit Seating Load. To calculate Initial Bolt Load to seat Gasket Joint, you need Width of u-collar in Gasket (b_g), Gasket Diameter (G) & Gasket Unit Seating Load (y_sl). With our tool, you need to enter the respective value for Width of u-collar in Gasket, Gasket Diameter & Gasket Unit Seating Load and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search