Inductance of Circuit from Cutting Frequency Calculator

✖Frequency of Cutting refers to how often a machine or tool is engaged to trim, shape, or remove material from a workpiece during the production process.ⓘ Frequency of Cutting [f_cut]			+10% -10%
✖Capacitance is the ratio of the amount of electric charge stored on a conductor to a difference in electric potential.ⓘ Capacitance [C]			+10% -10%

✖Inductance is the tendency of an electric conductor to oppose a change in the electric current flowing through it.ⓘ Inductance of Circuit from Cutting Frequency [L]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Production Engineering Formula PDF PDF Image

Inductance of Circuit from Cutting Frequency Solution

STEP 0: Pre-Calculation Summary

Formula Used

Inductance = ((0.03/Frequency of Cutting)^2)/Capacitance
L = ((0.03/f_cut)^2)/C
This formula uses 3 Variables

Variables Used

Inductance - (Measured in Henry) - Inductance is the tendency of an electric conductor to oppose a change in the electric current flowing through it.
Frequency of Cutting - (Measured in Hertz) - Frequency of Cutting refers to how often a machine or tool is engaged to trim, shape, or remove material from a workpiece during the production process.
Capacitance - (Measured in Farad) - Capacitance is the ratio of the amount of electric charge stored on a conductor to a difference in electric potential.

STEP 1: Convert Input(s) to Base Unit

Frequency of Cutting: 0.005 Cycle per Second --> 0.005 Hertz (Check conversion here)
Capacitance: 6.3 Farad --> 6.3 Farad No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

L = ((0.03/f_cut)^2)/C --> ((0.03/0.005)^2)/6.3

Evaluating ... ...

L = 5.71428571428571

STEP 3: Convert Result to Output's Unit

5.71428571428571 Henry --> No Conversion Required

FINAL ANSWER

5.71428571428571 ≈ 5.714286 Henry <-- Inductance

(Calculation completed in 00.007 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » System Analysis in EDM » Relaxation Circuit used for Generating Pulses in EDM » Frequency of Cutting » Inductance of Circuit from Cutting Frequency

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Vaibhav Malani

National Institute of Technology (NIT), Tiruchirapalli

Vaibhav Malani has verified this Calculator and 200+ more calculators!

< Frequency of Cutting Calculators

Frequency of Cutting from Capacitance and Inductance

LaTeX Go Frequency of Cutting = 0.03/sqrt(Inductance*Capacitance)

Frequency of Cutting using Charging and Sparking Time

LaTeX Go Frequency of Cutting = 1/(Sparking Time+Charging Time)

Sparking Time from Frequency of Cutting

LaTeX Go Sparking Time = 1/Frequency of Cutting-Charging Time

Charging Time from Cutting Frequency

LaTeX Go Charging Time = 1/Frequency of Cutting-Sparking Time

Inductance of Circuit from Cutting Frequency Formula

LaTeX Go

Inductance = ((0.03/Frequency of Cutting)^2)/Capacitance
L = ((0.03/f_cut)^2)/C

How the spark is produced in Electric Discharge Machining ?

A typical circuit used for supplying the power to an EDM machine is named as the relaxation circuit. The circuit consists of a DC power source, which charges the capacitor ‘C’ across a resistance ‘Rc’. Initially when the capacitor is in the uncharged condition, when the power supply is on with a voltage of Vo, a heavy current, ic, will flow in the circuit as shown to charge the capacitor.The relaxation circuit as explained above was used in the early EDM machines. They are limited to the low material removal rates for fine finish, which limits its application. This can be explained from the fact that the time spent on charging the capacitor is quite large during which time, no machining can actually take place. Thus the material removal rates are low.

How to Calculate Inductance of Circuit from Cutting Frequency?

Inductance of Circuit from Cutting Frequency calculator uses Inductance = ((0.03/Frequency of Cutting)^2)/Capacitance to calculate the Inductance, Inductance of circuit from cutting frequency formula is defined as the equivalent inductance of the inductors associated with the sparking circuit of the EDM. Inductance is denoted by L symbol.

How to calculate Inductance of Circuit from Cutting Frequency using this online calculator? To use this online calculator for Inductance of Circuit from Cutting Frequency, enter Frequency of Cutting (f_cut) & Capacitance (C) and hit the calculate button. Here is how the Inductance of Circuit from Cutting Frequency calculation can be explained with given input values -> 1.3E-5 = ((0.03/0.005)^2)/6.3.

FAQ

What is Inductance of Circuit from Cutting Frequency?

Inductance of circuit from cutting frequency formula is defined as the equivalent inductance of the inductors associated with the sparking circuit of the EDM and is represented as L = ((0.03/f_cut)^2)/C or Inductance = ((0.03/Frequency of Cutting)^2)/Capacitance. Frequency of Cutting refers to how often a machine or tool is engaged to trim, shape, or remove material from a workpiece during the production process & Capacitance is the ratio of the amount of electric charge stored on a conductor to a difference in electric potential.

How to calculate Inductance of Circuit from Cutting Frequency?

Inductance of circuit from cutting frequency formula is defined as the equivalent inductance of the inductors associated with the sparking circuit of the EDM is calculated using Inductance = ((0.03/Frequency of Cutting)^2)/Capacitance. To calculate Inductance of Circuit from Cutting Frequency, you need Frequency of Cutting (f_cut) & Capacitance (C). With our tool, you need to enter the respective value for Frequency of Cutting & Capacitance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search