LCM calculator

Incident Current using Impedance-1 (Line PL) Calculator

Engineering Chemistry Financial Health More >>

↳

Electrical Chemical Engineering Civil Electronics More >>

⤿

Power System Circuit Graph Theory Control System Electrical Circuit More >>

⤿

Transmission Lines Battery Life FACTS Devices Fault More >>

⤿

Transient Line Performance Characteristics Long Transmission Line Medium Line More >>

⤿

Travelling Waves

⤿

Different Cases for Reflection and Transmission Incident Wave Reflected Waves Relation Between Coefficients More >>

⤿

Line With Parallel Loads Line Is Open Circuited Line Is Short Circuited Load IS Open Circuited More >>

⤿

Impedance 1,2 and 3 Transmitted Coefficient OF Current Transmitted Current 1,2 and 3

✖The Incident Voltage on the transmission line is equal to half the generator voltage.ⓘ Incident Voltage [V_i]			+10% -10%
✖The Impedance of Primary Winding is the total of primary Resistance and Reactance.ⓘ Impedance of Primary Winding [Z₁]			+10% -10%

✖Incident Current is the Current wave that is traveling from the sending end to the receiving end of the Transmission line during any transient condition.ⓘ Incident Current using Impedance-1 (Line PL) [I_i]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Transmission Lines Formula PDF PDF Image

Incident Current using Impedance-1 (Line PL) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Incident Current = Incident Voltage/Impedance of Primary Winding
I_i = V_i/Z₁
This formula uses 3 Variables

Variables Used

Incident Current - (Measured in Ampere) - Incident Current is the Current wave that is traveling from the sending end to the receiving end of the Transmission line during any transient condition.
Incident Voltage - (Measured in Volt) - The Incident Voltage on the transmission line is equal to half the generator voltage.
Impedance of Primary Winding - (Measured in Ohm) - The Impedance of Primary Winding is the total of primary Resistance and Reactance.

STEP 1: Convert Input(s) to Base Unit

Incident Voltage: 6 Volt --> 6 Volt No Conversion Required
Impedance of Primary Winding: 18 Ohm --> 18 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

I_i = V_i/Z₁ --> 6/18

Evaluating ... ...

I_i = 0.333333333333333

STEP 3: Convert Result to Output's Unit

0.333333333333333 Ampere --> No Conversion Required

FINAL ANSWER

0.333333333333333 ≈ 0.333333 Ampere <-- Incident Current

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Transmission Lines » Transient » Travelling Waves » Different Cases for Reflection and Transmission » Line With Parallel Loads » Incident Current using Impedance-1 (Line PL)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Line With Parallel Loads Calculators

Reflected Current using Transmitted Current-3 and 2 (Line PL)

LaTeX Go Reflected Current = Incident Current-Transmitted Current-Transmitted Current

Incident Current using Transmitted Current-3 and 2 (Line PL)

LaTeX Go Incident Current = Reflected Current-Transmitted Current-Transmitted Current

Transmitted Voltage using Transmitted Current-2 (Line PL)

LaTeX Go Transmitted Voltage = Transmitted Current*Impedance of Secondary Winding

Transmitted Voltage using Transmitted Current-3 (Line PL)

LaTeX Go Transmitted Voltage = Transmitted Current*Impedance of Tertiary Winding

Incident Current using Impedance-1 (Line PL) Formula

LaTeX Go

Incident Current = Incident Voltage/Impedance of Primary Winding
I_i = V_i/Z₁

What is impedance-1?

Impedance-1 is a measure of the overall opposition of a circuit to current-1, in other words: how much the circuit impedes the flow of charge. It is like resistance, but it also takes into account the effects of capacitance and inductance. Impedance-1 is measured in ohms.

How to Calculate Incident Current using Impedance-1 (Line PL)?

Incident Current using Impedance-1 (Line PL) calculator uses Incident Current = Incident Voltage/Impedance of Primary Winding to calculate the Incident Current, The Incident Current using Impedance-1 (line PL) formula is defined as the current wave that is traveling from the sending end to the receiving end of the Transmission line. Incident Current is denoted by I_i symbol.

How to calculate Incident Current using Impedance-1 (Line PL) using this online calculator? To use this online calculator for Incident Current using Impedance-1 (Line PL), enter Incident Voltage (V_i) & Impedance of Primary Winding (Z₁) and hit the calculate button. Here is how the Incident Current using Impedance-1 (Line PL) calculation can be explained with given input values -> 0.333333 = 6/18.

FAQ

What is Incident Current using Impedance-1 (Line PL)?

The Incident Current using Impedance-1 (line PL) formula is defined as the current wave that is traveling from the sending end to the receiving end of the Transmission line and is represented as I_i = V_i/Z₁ or Incident Current = Incident Voltage/Impedance of Primary Winding. The Incident Voltage on the transmission line is equal to half the generator voltage & The Impedance of Primary Winding is the total of primary Resistance and Reactance.

How to calculate Incident Current using Impedance-1 (Line PL)?

The Incident Current using Impedance-1 (line PL) formula is defined as the current wave that is traveling from the sending end to the receiving end of the Transmission line is calculated using Incident Current = Incident Voltage/Impedance of Primary Winding. To calculate Incident Current using Impedance-1 (Line PL), you need Incident Voltage (V_i) & Impedance of Primary Winding (Z₁). With our tool, you need to enter the respective value for Incident Voltage & Impedance of Primary Winding and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Incident Current?

In this formula, Incident Current uses Incident Voltage & Impedance of Primary Winding. We can use 3 other way(s) to calculate the same, which is/are as follows -

Incident Current = Reflected Current-Transmitted Current-Transmitted Current
Incident Current = Transmitted Current/Transmission Coefficient of Current
Incident Current = Transmitted Current/Transmission Coefficient of Current

Home

FREE PDFs

🔍 Search