Hull Cutoff Magnetic Flux Density Calculator

✖Distance Between Anode and Cathode refers to the placing distance between the anode and cathode terminal of a magnetron.ⓘ Distance Between Anode and Cathode [d]			+10% -10%
✖Anode Voltage is the voltage applied to the anode or plate of a vacuum tube to attract and collect the electrons in the beam after they have passed through the device.ⓘ Anode Voltage [V₀]			+10% -10%

✖Hull Cutoff Magnetic Flux Density is the minimum magnetic flux density required to prevent electrons from reaching the anode in a vacuum tube.ⓘ Hull Cutoff Magnetic Flux Density [B_0c]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Magnetron Oscillator Formulas PDF PDF Image

Hull Cutoff Magnetic Flux Density Solution

STEP 0: Pre-Calculation Summary

Formula Used

Hull Cutoff Magnetic Flux Density = (1/Distance Between Anode and Cathode)*sqrt(2*([Mass-e]/[Charge-e])*Anode Voltage)
B_0c = (1/d)*sqrt(2*([Mass-e]/[Charge-e])*V₀)
This formula uses 2 Constants, 1 Functions, 3 Variables

Constants Used

[Charge-e] - Charge of electron Value Taken As 1.60217662E-19
[Mass-e] - Mass of electron Value Taken As 9.10938356E-31

Functions Used

sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Hull Cutoff Magnetic Flux Density - (Measured in Tesla) - Hull Cutoff Magnetic Flux Density is the minimum magnetic flux density required to prevent electrons from reaching the anode in a vacuum tube.
Distance Between Anode and Cathode - (Measured in Meter) - Distance Between Anode and Cathode refers to the placing distance between the anode and cathode terminal of a magnetron.
Anode Voltage - (Measured in Volt) - Anode Voltage is the voltage applied to the anode or plate of a vacuum tube to attract and collect the electrons in the beam after they have passed through the device.

STEP 1: Convert Input(s) to Base Unit

Distance Between Anode and Cathode: 0.06 Meter --> 0.06 Meter No Conversion Required
Anode Voltage: 26000 Volt --> 26000 Volt No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

B_0c = (1/d)*sqrt(2*([Mass-e]/[Charge-e])*V₀) --> (1/0.06)*sqrt(2*([Mass-e]/[Charge-e])*26000)

Evaluating ... ...

B_0c = 0.00906232683169974

STEP 3: Convert Result to Output's Unit

0.00906232683169974 Tesla -->0.00906232683169974 Weber per Square Meter (Check conversion here)

FINAL ANSWER

0.00906232683169974 ≈ 0.009062 Weber per Square Meter <-- Hull Cutoff Magnetic Flux Density

(Calculation completed in 00.011 seconds)

You are here -

Home » Engineering » Electronics » Microwave Theory » Microwave Tubes and Circuits » Magnetron Oscillator » Hull Cutoff Magnetic Flux Density

Credits

Created by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has created this Calculator and 900+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< Magnetron Oscillator Calculators

Repetition Frequency of Pulse

LaTeX Go Repetition Frequency = (Spectral Line Frequency-Carrier Frequency)/Number of Samples

Receiver Sensitivity

LaTeX Go Receiver Sensitivity = Receiver Noise Floor+Signal Noise Ratio

Characteristic Admittance

LaTeX Go Characteristic Admittance = 1/Characteristic Impedance

RF Pulse Width

LaTeX Go RF Pulse Width = 1/(2*Bandwidth)

Hull Cutoff Magnetic Flux Density Formula

LaTeX Go

Hull Cutoff Magnetic Flux Density = (1/Distance Between Anode and Cathode)*sqrt(2*([Mass-e]/[Charge-e])*Anode Voltage)
B_0c = (1/d)*sqrt(2*([Mass-e]/[Charge-e])*V₀)

Magnetron is based on which principle?

The magnetron is based on the principle of interaction between the electron beam and the traveling electromagnetic RF waves

How to Calculate Hull Cutoff Magnetic Flux Density?

Hull Cutoff Magnetic Flux Density calculator uses Hull Cutoff Magnetic Flux Density = (1/Distance Between Anode and Cathode)*sqrt(2*([Mass-e]/[Charge-e])*Anode Voltage) to calculate the Hull Cutoff Magnetic Flux Density, The Hull Cutoff Magnetic Flux Density formula is the minimum magnetic flux density required to prevent electrons from reaching the anode in a vacuum tube. It is also referred to as the Anode cutoff magnetic flux density. Hull Cutoff Magnetic Flux Density is denoted by B_0c symbol.

How to calculate Hull Cutoff Magnetic Flux Density using this online calculator? To use this online calculator for Hull Cutoff Magnetic Flux Density, enter Distance Between Anode and Cathode (d) & Anode Voltage (V₀) and hit the calculate button. Here is how the Hull Cutoff Magnetic Flux Density calculation can be explained with given input values -> 0.009062 = (1/0.06)*sqrt(2*([Mass-e]/[Charge-e])*26000).

FAQ

What is Hull Cutoff Magnetic Flux Density?

The Hull Cutoff Magnetic Flux Density formula is the minimum magnetic flux density required to prevent electrons from reaching the anode in a vacuum tube. It is also referred to as the Anode cutoff magnetic flux density and is represented as B_0c = (1/d)*sqrt(2*([Mass-e]/[Charge-e])*V₀) or Hull Cutoff Magnetic Flux Density = (1/Distance Between Anode and Cathode)*sqrt(2*([Mass-e]/[Charge-e])*Anode Voltage). Distance Between Anode and Cathode refers to the placing distance between the anode and cathode terminal of a magnetron & Anode Voltage is the voltage applied to the anode or plate of a vacuum tube to attract and collect the electrons in the beam after they have passed through the device.

How to calculate Hull Cutoff Magnetic Flux Density?

The Hull Cutoff Magnetic Flux Density formula is the minimum magnetic flux density required to prevent electrons from reaching the anode in a vacuum tube. It is also referred to as the Anode cutoff magnetic flux density is calculated using Hull Cutoff Magnetic Flux Density = (1/Distance Between Anode and Cathode)*sqrt(2*([Mass-e]/[Charge-e])*Anode Voltage). To calculate Hull Cutoff Magnetic Flux Density, you need Distance Between Anode and Cathode (d) & Anode Voltage (V₀). With our tool, you need to enter the respective value for Distance Between Anode and Cathode & Anode Voltage and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search