Greatest Safe Load for Channel or Z Bar when Load is Distributed Calculator

✖Cross Sectional Area of Beam the area of a two-dimensional shape that is obtained when a three-dimensional shape is sliced perpendicular to some specified axis at a point.ⓘ Cross Sectional Area of Beam [A_cs]			+10% -10%
✖Depth of Beam is the overall depth of the cross-section of the beam perpendicular to the axis of the beam.ⓘ Depth of Beam [d_b]			+10% -10%
✖Length of Beam is the center to center distance between the supports or the effective length of the beam.ⓘ Length of Beam [L]			+10% -10%

✖Greatest Safe Distributed Load is that load which acts over a considerable length or over a length which is measurable. Distributed load is measured as per unit length.ⓘ Greatest Safe Load for Channel or Z Bar when Load is Distributed [W_d]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Moving Loads and Influence Lines for Beams Formulas PDF PDF Image

Greatest Safe Load for Channel or Z Bar when Load is Distributed Solution

STEP 0: Pre-Calculation Summary

Formula Used

Greatest Safe Distributed Load = (3050*Cross Sectional Area of Beam*Depth of Beam)/Length of Beam
W_d = (3050*A_cs*d_b)/L
This formula uses 4 Variables

Variables Used

Greatest Safe Distributed Load - (Measured in Newton) - Greatest Safe Distributed Load is that load which acts over a considerable length or over a length which is measurable. Distributed load is measured as per unit length.
Cross Sectional Area of Beam - (Measured in Square Meter) - Cross Sectional Area of Beam the area of a two-dimensional shape that is obtained when a three-dimensional shape is sliced perpendicular to some specified axis at a point.
Depth of Beam - (Measured in Meter) - Depth of Beam is the overall depth of the cross-section of the beam perpendicular to the axis of the beam.
Length of Beam - (Measured in Meter) - Length of Beam is the center to center distance between the supports or the effective length of the beam.

STEP 1: Convert Input(s) to Base Unit

Cross Sectional Area of Beam: 13 Square Meter --> 13 Square Meter No Conversion Required
Depth of Beam: 10.01 Inch --> 0.254254000001017 Meter (Check conversion here)
Length of Beam: 10.02 Foot --> 3.05409600001222 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

W_d = (3050*A_cs*d_b)/L --> (3050*13*0.254254000001017)/3.05409600001222

Evaluating ... ...

W_d = 3300.86909514304

STEP 3: Convert Result to Output's Unit

3300.86909514304 Newton -->3.30086909514304 Kilonewton (Check conversion here)

FINAL ANSWER

3.30086909514304 ≈ 3.300869 Kilonewton <-- Greatest Safe Distributed Load

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Structural Engineering » Structural Analysis » Moving Loads and Influence Lines for Beams » Safe Loads » Greatest Safe Load for Channel or Z Bar when Load is Distributed

Credits

Created by Rudrani Tidke

Cummins College of Engineering for Women (CCEW), Pune

Rudrani Tidke has created this Calculator and 100+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< Safe Loads Calculators

Greatest Safe Load for Hollow Rectangle when Load is Distributed

LaTeX Go Greatest Safe Distributed Load = 1780*(Cross Sectional Area of Beam*Depth of Beam-Interior Cross-Sectional Area of Beam*Interior Depth of Beam)/Distance between Supports

Greatest Safe Load for Hollow Rectangle when Load in Middle

LaTeX Go Greatest Safe Point Load = (890*(Cross Sectional Area of Beam*Depth of Beam-Interior Cross-Sectional Area of Beam*Interior Depth of Beam))/Length of Beam

Greatest Safe Load for Solid Rectangle when Load is Distributed

LaTeX Go Greatest Safe Distributed Load = 1780*Cross Sectional Area of Beam*Depth of Beam/Length of Beam

Greatest Safe Load for Solid Rectangle given Load in Middle

LaTeX Go Greatest Safe Point Load = 890*Cross Sectional Area of Beam*Depth of Beam/Length of Beam

Greatest Safe Load for Channel or Z Bar when Load is Distributed Formula

LaTeX Go

Greatest Safe Distributed Load = (3050*Cross Sectional Area of Beam*Depth of Beam)/Length of Beam
W_d = (3050*A_cs*d_b)/L

What is Greatest Safe Load for Channel or Z Bar when Load is Distributed?

Greatest Safe Load is the maximum point load that can be applied at the beam of Channel or Z Bar cross-section without fear of it collapsing.It is sometimes stated as the Normal Working Load (NWL) is the mass or force that a piece of lifting equipment, lifting device, or accessory can safely use to lift, suspend, or lower a mass without fear of breaking.

How to Calculate Greatest Safe Load for Channel or Z Bar when Load is Distributed?

Greatest Safe Load for Channel or Z Bar when Load is Distributed calculator uses Greatest Safe Distributed Load = (3050*Cross Sectional Area of Beam*Depth of Beam)/Length of Beam to calculate the Greatest Safe Distributed Load, The Greatest Safe Load for Channel or Z Bar when Load is Distributed formula is defined as a distributed load applied on a Channel or Z Bar structure which does not produce stresses in excess of allowable stresses. Greatest Safe Distributed Load is denoted by W_d symbol.

How to calculate Greatest Safe Load for Channel or Z Bar when Load is Distributed using this online calculator? To use this online calculator for Greatest Safe Load for Channel or Z Bar when Load is Distributed, enter Cross Sectional Area of Beam (A_cs), Depth of Beam (d_b) & Length of Beam (L) and hit the calculate button. Here is how the Greatest Safe Load for Channel or Z Bar when Load is Distributed calculation can be explained with given input values -> 0.003307 = (3050*13*0.254254000001017)/3.05409600001222.

FAQ

What is Greatest Safe Load for Channel or Z Bar when Load is Distributed?

The Greatest Safe Load for Channel or Z Bar when Load is Distributed formula is defined as a distributed load applied on a Channel or Z Bar structure which does not produce stresses in excess of allowable stresses and is represented as W_d = (3050*A_cs*d_b)/L or Greatest Safe Distributed Load = (3050*Cross Sectional Area of Beam*Depth of Beam)/Length of Beam. Cross Sectional Area of Beam the area of a two-dimensional shape that is obtained when a three-dimensional shape is sliced perpendicular to some specified axis at a point, Depth of Beam is the overall depth of the cross-section of the beam perpendicular to the axis of the beam & Length of Beam is the center to center distance between the supports or the effective length of the beam.

How to calculate Greatest Safe Load for Channel or Z Bar when Load is Distributed?

The Greatest Safe Load for Channel or Z Bar when Load is Distributed formula is defined as a distributed load applied on a Channel or Z Bar structure which does not produce stresses in excess of allowable stresses is calculated using Greatest Safe Distributed Load = (3050*Cross Sectional Area of Beam*Depth of Beam)/Length of Beam. To calculate Greatest Safe Load for Channel or Z Bar when Load is Distributed, you need Cross Sectional Area of Beam (A_cs), Depth of Beam (d_b) & Length of Beam (L). With our tool, you need to enter the respective value for Cross Sectional Area of Beam, Depth of Beam & Length of Beam and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Greatest Safe Distributed Load?

In this formula, Greatest Safe Distributed Load uses Cross Sectional Area of Beam, Depth of Beam & Length of Beam. We can use 3 other way(s) to calculate the same, which is/are as follows -

Greatest Safe Distributed Load = 1780*Cross Sectional Area of Beam*Depth of Beam/Length of Beam
Greatest Safe Distributed Load = 1780*(Cross Sectional Area of Beam*Depth of Beam-Interior Cross-Sectional Area of Beam*Interior Depth of Beam)/Distance between Supports
Greatest Safe Distributed Load = 1333*(Cross Sectional Area of Beam*Depth of Beam)/Length of Beam

Home

FREE PDFs

🔍 Search