Gap Resistance from Electrolyte Flow Rate Calculator

✖Volume Flow Rate is the volume of fluid that passes per unit of time.ⓘ Volume Flow Rate [q]			+10% -10%
✖The Density of Electrolyte shows the denseness of that electrolyte in a specific given area, this is taken as mass per unit volume of a given object.ⓘ Density of Electrolyte [ρ_e]			+10% -10%
✖Specific Heat Capacity of Electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount.ⓘ Specific Heat Capacity of Electrolyte [c_e]			+10% -10%
✖Boiling Point of Electrolyte is the temperature at which a liquid starts to boil and transforms to vapor.ⓘ Boiling Point of Electrolyte [θ_B]			+10% -10%
✖Ambient Air Temperature to the temperature of the air surrounding a particular object or area.ⓘ Ambient Air Temperature [θ_o]			+10% -10%
✖Electric current is the rate of flow of electric charge through a circuit, measured in amperes.ⓘ Electric Current [I]			+10% -10%

✖Resistance of Gap Between Work And Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.ⓘ Gap Resistance from Electrolyte Flow Rate [R]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Metal Machining Formula PDF PDF Image

Gap Resistance from Electrolyte Flow Rate Solution

STEP 0: Pre-Calculation Summary

Formula Used

Resistance of Gap Between Work And Tool = (Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))/Electric Current^2
R = (q*ρ_e*c_e*(θ_B-θ_o))/I^2
This formula uses 7 Variables

Variables Used

Resistance of Gap Between Work And Tool - (Measured in Ohm) - Resistance of Gap Between Work And Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.
Volume Flow Rate - (Measured in Cubic Meter per Second) - Volume Flow Rate is the volume of fluid that passes per unit of time.
Density of Electrolyte - (Measured in Kilogram per Cubic Meter) - The Density of Electrolyte shows the denseness of that electrolyte in a specific given area, this is taken as mass per unit volume of a given object.
Specific Heat Capacity of Electrolyte - (Measured in Joule per Kilogram per K) - Specific Heat Capacity of Electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount.
Boiling Point of Electrolyte - (Measured in Kelvin) - Boiling Point of Electrolyte is the temperature at which a liquid starts to boil and transforms to vapor.
Ambient Air Temperature - (Measured in Kelvin) - Ambient Air Temperature to the temperature of the air surrounding a particular object or area.
Electric Current - (Measured in Ampere) - Electric current is the rate of flow of electric charge through a circuit, measured in amperes.

STEP 1: Convert Input(s) to Base Unit

Volume Flow Rate: 47990.86 Cubic Millimeter per Second --> 4.799086E-05 Cubic Meter per Second (Check conversion here)
Density of Electrolyte: 997 Kilogram per Cubic Meter --> 997 Kilogram per Cubic Meter No Conversion Required
Specific Heat Capacity of Electrolyte: 4.18 Kilojoule per Kilogram per K --> 4180 Joule per Kilogram per K (Check conversion here)
Boiling Point of Electrolyte: 368.15 Kelvin --> 368.15 Kelvin No Conversion Required
Ambient Air Temperature: 308.15 Kelvin --> 308.15 Kelvin No Conversion Required
Electric Current: 1000 Ampere --> 1000 Ampere No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

R = (q*ρ_e*c_e*(θ_B-θ_o))/I^2 --> (4.799086E-05*997*4180*(368.15-308.15))/1000^2

Evaluating ... ...

R = 0.011999999364936

STEP 3: Convert Result to Output's Unit

0.011999999364936 Ohm --> No Conversion Required

FINAL ANSWER

0.011999999364936 ≈ 0.012 Ohm <-- Resistance of Gap Between Work And Tool

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Electrochemical Machining » Gap Resistance » Gap Resistance from Electrolyte Flow Rate

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has verified this Calculator and 400+ more calculators!

< Gap Resistance Calculators

Density of Work Material given Gap between Tool and Work Surface

LaTeX Go Work Piece Density = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Feed Speed*Gap Between Tool And Work Surface)

Gap between Tool and Work Surface

LaTeX Go Gap Between Tool And Work Surface = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Work Piece Density*Feed Speed)

Specific Resistivity of Electrolyte given Supply Current

LaTeX Go Specific Resistance of The Electrolyte = Area of Penetration*Supply Voltage/(Gap Between Tool And Work Surface*Electric Current)

Gap between Tool and Work Surface given Supply Current

LaTeX Go Gap Between Tool And Work Surface = Area of Penetration*Supply Voltage/(Specific Resistance of The Electrolyte*Electric Current)

Gap Resistance from Electrolyte Flow Rate Formula

LaTeX Go

What is Faraday's I law of electrolysis ?

The first law of Faraday’s electrolysis states that the chemical change produced during electrolysis is proportional to the current passed and the electrochemical equivalence of the anode material.

How to Calculate Gap Resistance from Electrolyte Flow Rate?

Gap Resistance from Electrolyte Flow Rate calculator uses Resistance of Gap Between Work And Tool = (Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))/Electric Current^2 to calculate the Resistance of Gap Between Work And Tool, The Gap resistance from electrolyte flow rate formula is defined as the resistance offered by the gap/space present between the tool and workpiece during ECM. Resistance of Gap Between Work And Tool is denoted by R symbol.

How to calculate Gap Resistance from Electrolyte Flow Rate using this online calculator? To use this online calculator for Gap Resistance from Electrolyte Flow Rate, enter Volume Flow Rate (q), Density of Electrolyte (ρ_e), Specific Heat Capacity of Electrolyte (c_e), Boiling Point of Electrolyte (θ_B), Ambient Air Temperature (θ_o) & Electric Current (I) and hit the calculate button. Here is how the Gap Resistance from Electrolyte Flow Rate calculation can be explained with given input values -> 1.2E-5 = (4.799086E-05*997*4180*(368.15-308.15))/1000^2.

FAQ

What is Gap Resistance from Electrolyte Flow Rate?

The Gap resistance from electrolyte flow rate formula is defined as the resistance offered by the gap/space present between the tool and workpiece during ECM and is represented as R = (q*ρ_e*c_e*(θ_B-θ_o))/I^2 or Resistance of Gap Between Work And Tool = (Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))/Electric Current^2. Volume Flow Rate is the volume of fluid that passes per unit of time, The Density of Electrolyte shows the denseness of that electrolyte in a specific given area, this is taken as mass per unit volume of a given object, Specific Heat Capacity of Electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount, Boiling Point of Electrolyte is the temperature at which a liquid starts to boil and transforms to vapor, Ambient Air Temperature to the temperature of the air surrounding a particular object or area & Electric current is the rate of flow of electric charge through a circuit, measured in amperes.

How to calculate Gap Resistance from Electrolyte Flow Rate?

The Gap resistance from electrolyte flow rate formula is defined as the resistance offered by the gap/space present between the tool and workpiece during ECM is calculated using Resistance of Gap Between Work And Tool = (Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))/Electric Current^2. To calculate Gap Resistance from Electrolyte Flow Rate, you need Volume Flow Rate (q), Density of Electrolyte (ρ_e), Specific Heat Capacity of Electrolyte (c_e), Boiling Point of Electrolyte (θ_B), Ambient Air Temperature (θ_o) & Electric Current (I). With our tool, you need to enter the respective value for Volume Flow Rate, Density of Electrolyte, Specific Heat Capacity of Electrolyte, Boiling Point of Electrolyte, Ambient Air Temperature & Electric Current and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Resistance of Gap Between Work And Tool?

In this formula, Resistance of Gap Between Work And Tool uses Volume Flow Rate, Density of Electrolyte, Specific Heat Capacity of Electrolyte, Boiling Point of Electrolyte, Ambient Air Temperature & Electric Current. We can use 1 other way(s) to calculate the same, which is/are as follows -

Resistance of Gap Between Work And Tool = (Specific Resistance of The Electrolyte*Gap Between Tool And Work Surface)/Cross Sectional Area of Gap

Home

FREE PDFs

🔍 Search