Flow Rate of Electrolytes from Gap Resistance ECM Calculator

✖Electric current is the rate of flow of electric charge through a circuit, measured in amperes.ⓘ Electric Current [I]			+10% -10%
✖Resistance of Gap Between Work And Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.ⓘ Resistance of Gap Between Work And Tool [R]			+10% -10%
✖The Density of Electrolyte shows the denseness of that electrolyte in a specific given area, this is taken as mass per unit volume of a given object.ⓘ Density of Electrolyte [ρ_e]			+10% -10%
✖Specific Heat Capacity of Electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount.ⓘ Specific Heat Capacity of Electrolyte [c_e]			+10% -10%
✖Boiling Point of Electrolyte is the temperature at which a liquid starts to boil and transforms to vapor.ⓘ Boiling Point of Electrolyte [θ_B]			+10% -10%
✖Ambient Air Temperature to the temperature of the air surrounding a particular object or area.ⓘ Ambient Air Temperature [θ_o]			+10% -10%

✖Volume Flow Rate is the volume of fluid that passes per unit of time.ⓘ Flow Rate of Electrolytes from Gap Resistance ECM [q]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Metal Machining Formula PDF PDF Image

Flow Rate of Electrolytes from Gap Resistance ECM Solution

STEP 0: Pre-Calculation Summary

Formula Used

Volume Flow Rate = (Electric Current^2*Resistance of Gap Between Work And Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))
q = (I^2*R)/(ρ_e*c_e*(θ_B-θ_o))
This formula uses 7 Variables

Variables Used

Volume Flow Rate - (Measured in Cubic Meter per Second) - Volume Flow Rate is the volume of fluid that passes per unit of time.
Electric Current - (Measured in Ampere) - Electric current is the rate of flow of electric charge through a circuit, measured in amperes.
Resistance of Gap Between Work And Tool - (Measured in Ohm) - Resistance of Gap Between Work And Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.
Density of Electrolyte - (Measured in Kilogram per Cubic Meter) - The Density of Electrolyte shows the denseness of that electrolyte in a specific given area, this is taken as mass per unit volume of a given object.
Specific Heat Capacity of Electrolyte - (Measured in Joule per Kilogram per K) - Specific Heat Capacity of Electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount.
Boiling Point of Electrolyte - (Measured in Kelvin) - Boiling Point of Electrolyte is the temperature at which a liquid starts to boil and transforms to vapor.
Ambient Air Temperature - (Measured in Kelvin) - Ambient Air Temperature to the temperature of the air surrounding a particular object or area.

STEP 1: Convert Input(s) to Base Unit

Electric Current: 1000 Ampere --> 1000 Ampere No Conversion Required
Resistance of Gap Between Work And Tool: 0.012 Ohm --> 0.012 Ohm No Conversion Required
Density of Electrolyte: 997 Kilogram per Cubic Meter --> 997 Kilogram per Cubic Meter No Conversion Required
Specific Heat Capacity of Electrolyte: 4.18 Kilojoule per Kilogram per K --> 4180 Joule per Kilogram per K (Check conversion here)
Boiling Point of Electrolyte: 368.15 Kelvin --> 368.15 Kelvin No Conversion Required
Ambient Air Temperature: 308.15 Kelvin --> 308.15 Kelvin No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

q = (I^2*R)/(ρ_e*c_e*(θ_B-θ_o)) --> (1000^2*0.012)/(997*4180*(368.15-308.15))

Evaluating ... ...

q = 4.79908625397724E-05

STEP 3: Convert Result to Output's Unit

4.79908625397724E-05 Cubic Meter per Second -->47990.8625397724 Cubic Millimeter per Second (Check conversion here)

FINAL ANSWER

47990.8625397724 ≈ 47990.86 Cubic Millimeter per Second <-- Volume Flow Rate

(Calculation completed in 00.008 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Electrochemical Machining » Gap Resistance » Flow Rate of Electrolytes from Gap Resistance ECM

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has verified this Calculator and 400+ more calculators!

< Gap Resistance Calculators

Density of Work Material given Gap between Tool and Work Surface

LaTeX Go Work Piece Density = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Feed Speed*Gap Between Tool And Work Surface)

Gap between Tool and Work Surface

LaTeX Go Gap Between Tool And Work Surface = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Work Piece Density*Feed Speed)

Specific Resistivity of Electrolyte given Supply Current

LaTeX Go Specific Resistance of The Electrolyte = Area of Penetration*Supply Voltage/(Gap Between Tool And Work Surface*Electric Current)

Gap between Tool and Work Surface given Supply Current

LaTeX Go Gap Between Tool And Work Surface = Area of Penetration*Supply Voltage/(Specific Resistance of The Electrolyte*Electric Current)

Flow Rate of Electrolytes from Gap Resistance ECM Formula

LaTeX Go

What is Faraday's I law of electrolysis ?

The first law of Faraday’s electrolysis states that the chemical change produced during electrolysis is proportional to the current passed and the electrochemical equivalence of the anode material.

How to Calculate Flow Rate of Electrolytes from Gap Resistance ECM?

Flow Rate of Electrolytes from Gap Resistance ECM calculator uses Volume Flow Rate = (Electric Current^2*Resistance of Gap Between Work And Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature)) to calculate the Volume Flow Rate, The flow rate of electrolytes from gap resistance ECM formula is used to determine the flow rate that is required to cool down the heat generated during machining. Volume Flow Rate is denoted by q symbol.

How to calculate Flow Rate of Electrolytes from Gap Resistance ECM using this online calculator? To use this online calculator for Flow Rate of Electrolytes from Gap Resistance ECM, enter Electric Current (I), Resistance of Gap Between Work And Tool (R), Density of Electrolyte (ρ_e), Specific Heat Capacity of Electrolyte (c_e), Boiling Point of Electrolyte (θ_B) & Ambient Air Temperature (θ_o) and hit the calculate button. Here is how the Flow Rate of Electrolytes from Gap Resistance ECM calculation can be explained with given input values -> 4.8E+13 = (1000^2*0.012)/(997*4180*(368.15-308.15)).

FAQ

What is Flow Rate of Electrolytes from Gap Resistance ECM?

The flow rate of electrolytes from gap resistance ECM formula is used to determine the flow rate that is required to cool down the heat generated during machining and is represented as q = (I^2*R)/(ρ_e*c_e*(θ_B-θ_o)) or Volume Flow Rate = (Electric Current^2*Resistance of Gap Between Work And Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature)). Electric current is the rate of flow of electric charge through a circuit, measured in amperes, Resistance of Gap Between Work And Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry, The Density of Electrolyte shows the denseness of that electrolyte in a specific given area, this is taken as mass per unit volume of a given object, Specific Heat Capacity of Electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount, Boiling Point of Electrolyte is the temperature at which a liquid starts to boil and transforms to vapor & Ambient Air Temperature to the temperature of the air surrounding a particular object or area.

How to calculate Flow Rate of Electrolytes from Gap Resistance ECM?

The flow rate of electrolytes from gap resistance ECM formula is used to determine the flow rate that is required to cool down the heat generated during machining is calculated using Volume Flow Rate = (Electric Current^2*Resistance of Gap Between Work And Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature)). To calculate Flow Rate of Electrolytes from Gap Resistance ECM, you need Electric Current (I), Resistance of Gap Between Work And Tool (R), Density of Electrolyte (ρ_e), Specific Heat Capacity of Electrolyte (c_e), Boiling Point of Electrolyte (θ_B) & Ambient Air Temperature (θ_o). With our tool, you need to enter the respective value for Electric Current, Resistance of Gap Between Work And Tool, Density of Electrolyte, Specific Heat Capacity of Electrolyte, Boiling Point of Electrolyte & Ambient Air Temperature and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search