Factor of Safety given Allowable Static Thrust Load on Ring Calculator

✖Conversion factor is to account for change from metric units used in development of the formula.ⓘ Conversion Factor [C]			+10% -10%
✖The Shaft Diameter is defined as the diameter of the hole in the iron laminations that contains the shaft.ⓘ Shaft Diameter [D]			+10% -10%
✖Ring thickness refers to the thickness of the metal when viewed from the side, or the profile, of the ring.ⓘ Ring Thickness [t]			+10% -10%
✖Shear strength of metal ring is defined as its ability to resist forces that cause the material's internal structure to slide against itself.ⓘ Shear Strength of Metal Ring [τ_s]			+10% -10%
✖Allowable static thrust load on ring is the amount of measured force directed at and from a turning mechanism.ⓘ Allowable Static Thrust Load on Ring [F_rT]			+10% -10%

✖Safety factor otherwise called as factor of safety expresses how much stronger a system is than it needs to be for an intended load.ⓘ Factor of Safety given Allowable Static Thrust Load on Ring [F_s]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Retaining Rings and Circlips Formulas PDF PDF Image

Factor of Safety given Allowable Static Thrust Load on Ring Solution

STEP 0: Pre-Calculation Summary

Formula Used

Safety Factor = (Conversion Factor*Shaft Diameter*Ring Thickness*pi*Shear Strength of Metal Ring)/Allowable Static Thrust Load on Ring
F_s = (C*D*t*pi*τ_s)/F_rT
This formula uses 1 Constants, 6 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Safety Factor - Safety factor otherwise called as factor of safety expresses how much stronger a system is than it needs to be for an intended load.
Conversion Factor - Conversion factor is to account for change from metric units used in development of the formula.
Shaft Diameter - (Measured in Meter) - The Shaft Diameter is defined as the diameter of the hole in the iron laminations that contains the shaft.
Ring Thickness - (Measured in Meter) - Ring thickness refers to the thickness of the metal when viewed from the side, or the profile, of the ring.
Shear Strength of Metal Ring - (Measured in Newton) - Shear strength of metal ring is defined as its ability to resist forces that cause the material's internal structure to slide against itself.
Allowable Static Thrust Load on Ring - (Measured in Newton) - Allowable static thrust load on ring is the amount of measured force directed at and from a turning mechanism.

STEP 1: Convert Input(s) to Base Unit

Conversion Factor: 0.11 --> No Conversion Required
Shaft Diameter: 3.6 Meter --> 3.6 Meter No Conversion Required
Ring Thickness: 5 Meter --> 5 Meter No Conversion Required
Shear Strength of Metal Ring: 6 Newton --> 6 Newton No Conversion Required
Allowable Static Thrust Load on Ring: 6.4 Newton --> 6.4 Newton No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

F_s = (C*D*t*pi*τ_s)/F_rT --> (0.11*3.6*5*pi*6)/6.4

Evaluating ... ...

F_s = 5.83158136322605

STEP 3: Convert Result to Output's Unit

5.83158136322605 --> No Conversion Required

FINAL ANSWER

5.83158136322605 ≈ 5.831581 <-- Safety Factor

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Design of Machine Elements » Design of Coupling » Retaining Rings and Circlips » Mechanical » Factor of Safety » Factor of Safety given Allowable Static Thrust Load on Ring

Credits

Created by sanjay shiva

national institute of technology hamirpur (NITH ), hamirpur , himachal pradesh

sanjay shiva has created this Calculator and 100+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Factor of Safety Calculators

Factor of Safety given allowable Static Thrust Load on Groove

LaTeX Go Factor of Safety = (Conversion Factor*Shaft Diameter*Depth of Groove*pi*Tensile Yield Strength of Groove Material)/(Allowable Static Thrust Load on Groove Wall*Reduction Factor)

Factor of Safety given Allowable Static Thrust Load on Ring

LaTeX Go Safety Factor = (Conversion Factor*Shaft Diameter*Ring Thickness*pi*Shear Strength of Metal Ring)/Allowable Static Thrust Load on Ring

Factor of Safety given Allowable Static Thrust Load on Ring Formula

LaTeX Go

Safety Factor = (Conversion Factor*Shaft Diameter*Ring Thickness*pi*Shear Strength of Metal Ring)/Allowable Static Thrust Load on Ring
F_s = (C*D*t*pi*τ_s)/F_rT

What is static thrust load?

Static thrust load is the amount of measured force directed at and from a turning mechanism. As the mechanism such as a gear turns on a shaft, there is both load emitted from the gear in the direction it is turning as well as against the shaft it is turning on, either forward or to the rear.

How to Calculate Factor of Safety given Allowable Static Thrust Load on Ring?

Factor of Safety given Allowable Static Thrust Load on Ring calculator uses Safety Factor = (Conversion Factor*Shaft Diameter*Ring Thickness*pi*Shear Strength of Metal Ring)/Allowable Static Thrust Load on Ring to calculate the Safety Factor, The Factor of Safety given Allowable Static Thrust Load on Ring formula is defined as how much stronger a system is than it needs to be for an intended load. Safety Factor is denoted by F_s symbol.

How to calculate Factor of Safety given Allowable Static Thrust Load on Ring using this online calculator? To use this online calculator for Factor of Safety given Allowable Static Thrust Load on Ring, enter Conversion Factor (C), Shaft Diameter (D), Ring Thickness (t), Shear Strength of Metal Ring (τ_s) & Allowable Static Thrust Load on Ring (F_rT) and hit the calculate button. Here is how the Factor of Safety given Allowable Static Thrust Load on Ring calculation can be explained with given input values -> 5.831581 = (0.11*3.6*5*pi*6)/6.4.

FAQ

What is Factor of Safety given Allowable Static Thrust Load on Ring?

The Factor of Safety given Allowable Static Thrust Load on Ring formula is defined as how much stronger a system is than it needs to be for an intended load and is represented as F_s = (C*D*t*pi*τ_s)/F_rT or Safety Factor = (Conversion Factor*Shaft Diameter*Ring Thickness*pi*Shear Strength of Metal Ring)/Allowable Static Thrust Load on Ring. Conversion factor is to account for change from metric units used in development of the formula, The Shaft Diameter is defined as the diameter of the hole in the iron laminations that contains the shaft, Ring thickness refers to the thickness of the metal when viewed from the side, or the profile, of the ring, Shear strength of metal ring is defined as its ability to resist forces that cause the material's internal structure to slide against itself & Allowable static thrust load on ring is the amount of measured force directed at and from a turning mechanism.

How to calculate Factor of Safety given Allowable Static Thrust Load on Ring?

The Factor of Safety given Allowable Static Thrust Load on Ring formula is defined as how much stronger a system is than it needs to be for an intended load is calculated using Safety Factor = (Conversion Factor*Shaft Diameter*Ring Thickness*pi*Shear Strength of Metal Ring)/Allowable Static Thrust Load on Ring. To calculate Factor of Safety given Allowable Static Thrust Load on Ring, you need Conversion Factor (C), Shaft Diameter (D), Ring Thickness (t), Shear Strength of Metal Ring (τ_s) & Allowable Static Thrust Load on Ring (F_rT). With our tool, you need to enter the respective value for Conversion Factor, Shaft Diameter, Ring Thickness, Shear Strength of Metal Ring & Allowable Static Thrust Load on Ring and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search