Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation Calculator

✖The Rate of Heat Generation in Secondary Shear Zone is the rate of heat generation in the area surrounding the chip tool contact region.ⓘ Rate of Heat Generation in Secondary Shear Zone [P_f]			+10% -10%
✖The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius.ⓘ Specific Heat Capacity of Workpiece [C]			+10% -10%
✖Density of Work Piece is the mass per unit volume ratio of the material of workpiece.ⓘ Density of Work Piece [ρ_wp]			+10% -10%
✖Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).ⓘ Cutting Speed [V_cut]			+10% -10%
✖Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces.ⓘ Undeformed Chip Thickness [a_c]			+10% -10%
✖The Average Temp Rise of Chip in Secondary Shear Zone is defined as the amount of temperature rise in the secondary shear zone.ⓘ Average Temp Rise of Chip in Secondary Shear Zone [θ_f]			+10% -10%

✖Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.ⓘ Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation [d_cut]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Production Engineering Formula PDF PDF Image

Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation Solution

STEP 0: Pre-Calculation Summary

Formula Used

Depth of Cut = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of Work Piece*Cutting Speed*Undeformed Chip Thickness*Average Temp Rise of Chip in Secondary Shear Zone)
d_cut = P_f/(C*ρ_wp*V_cut*a_c*θ_f)
This formula uses 7 Variables

Variables Used

Depth of Cut - (Measured in Meter) - Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.
Rate of Heat Generation in Secondary Shear Zone - (Measured in Watt) - The Rate of Heat Generation in Secondary Shear Zone is the rate of heat generation in the area surrounding the chip tool contact region.
Specific Heat Capacity of Workpiece - (Measured in Joule per Kilogram per K) - The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius.
Density of Work Piece - (Measured in Kilogram per Cubic Meter) - Density of Work Piece is the mass per unit volume ratio of the material of workpiece.
Cutting Speed - (Measured in Meter per Second) - Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).
Undeformed Chip Thickness - (Measured in Meter) - Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces.
Average Temp Rise of Chip in Secondary Shear Zone - (Measured in Kelvin) - The Average Temp Rise of Chip in Secondary Shear Zone is defined as the amount of temperature rise in the secondary shear zone.

STEP 1: Convert Input(s) to Base Unit

Rate of Heat Generation in Secondary Shear Zone: 400 Watt --> 400 Watt No Conversion Required
Specific Heat Capacity of Workpiece: 502 Joule per Kilogram per K --> 502 Joule per Kilogram per K No Conversion Required
Density of Work Piece: 7200 Kilogram per Cubic Meter --> 7200 Kilogram per Cubic Meter No Conversion Required
Cutting Speed: 2 Meter per Second --> 2 Meter per Second No Conversion Required
Undeformed Chip Thickness: 0.25 Millimeter --> 0.00025 Meter (Check conversion here)
Average Temp Rise of Chip in Secondary Shear Zone: 88.5 Degree Celsius --> 88.5 Kelvin (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

d_cut = P_f/(C*ρ_wp*V_cut*a_c*θ_f) --> 400/(502*7200*2*0.00025*88.5)

Evaluating ... ...

d_cut = 0.00250098163529185

STEP 3: Convert Result to Output's Unit

0.00250098163529185 Meter -->2.50098163529185 Millimeter (Check conversion here)

FINAL ANSWER

2.50098163529185 ≈ 2.500982 Millimeter <-- Depth of Cut

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Metal Machining Dynamics » Temperatures in Metal Cutting » Temperature Rise » Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation

Credits

Created by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has created this Calculator and 300+ more calculators!

Verified by Kumar Siddhant

Indian Institute of Information Technology, Design and Manufacturing (IIITDM), Jabalpur

Kumar Siddhant has verified this Calculator and 100+ more calculators!

< Temperature Rise Calculators

Density of Material using Average Temperature Rise of material under Primary Shear Zone

LaTeX Go Density of Work Piece = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Average Temperature Rise*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Specific Heat given Average Temperature Rise of Material under Primary Shear Zone

LaTeX Go Specific Heat Capacity of Workpiece = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Average Temperature Rise*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Cutting Speed given Average Temperature Rise of Material under Primary Shear Zone

LaTeX Go Cutting Speed = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Average Temperature Rise*Undeformed Chip Thickness*Depth of Cut)

Average Temperature Rise of Material under Primary Deformation Zone

LaTeX Go Average Temperature Rise = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation Formula

LaTeX Go

What is depth of cut and how it is determined?

It is the total amount of metal removed per pass of the cutting tool. It is expressed in mm. It can vary and depend upon the type of tool and work material. Mathematically, it is half of the difference in diameters. The depth of cut (t) is the perpendicular distance measured from the machined surface to the uncut surface of the workpiece.

How to Calculate Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation?

Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation calculator uses Depth of Cut = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of Work Piece*Cutting Speed*Undeformed Chip Thickness*Average Temp Rise of Chip in Secondary Shear Zone) to calculate the Depth of Cut, The Depth of cut using Average Temperature rise of chip from Secondary Deformation is the total amount of metal removed per pass of the cutting tool. Depth of Cut is denoted by d_cut symbol.

How to calculate Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation using this online calculator? To use this online calculator for Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation, enter Rate of Heat Generation in Secondary Shear Zone (P_f), Specific Heat Capacity of Workpiece (C), Density of Work Piece (ρ_wp), Cutting Speed (V_cut), Undeformed Chip Thickness (a_c) & Average Temp Rise of Chip in Secondary Shear Zone (θ_f) and hit the calculate button. Here is how the Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation calculation can be explained with given input values -> 2500 = 400/(502*7200*2*0.00025*88.5).

FAQ

What is Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation?

The Depth of cut using Average Temperature rise of chip from Secondary Deformation is the total amount of metal removed per pass of the cutting tool and is represented as d_cut = P_f/(C*ρ_wp*V_cut*a_c*θ_f) or Depth of Cut = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of Work Piece*Cutting Speed*Undeformed Chip Thickness*Average Temp Rise of Chip in Secondary Shear Zone). The Rate of Heat Generation in Secondary Shear Zone is the rate of heat generation in the area surrounding the chip tool contact region, The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius, Density of Work Piece is the mass per unit volume ratio of the material of workpiece, Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute), Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces & The Average Temp Rise of Chip in Secondary Shear Zone is defined as the amount of temperature rise in the secondary shear zone.

How to calculate Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation?

The Depth of cut using Average Temperature rise of chip from Secondary Deformation is the total amount of metal removed per pass of the cutting tool is calculated using Depth of Cut = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of Work Piece*Cutting Speed*Undeformed Chip Thickness*Average Temp Rise of Chip in Secondary Shear Zone). To calculate Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation, you need Rate of Heat Generation in Secondary Shear Zone (P_f), Specific Heat Capacity of Workpiece (C), Density of Work Piece (ρ_wp), Cutting Speed (V_cut), Undeformed Chip Thickness (a_c) & Average Temp Rise of Chip in Secondary Shear Zone (θ_f). With our tool, you need to enter the respective value for Rate of Heat Generation in Secondary Shear Zone, Specific Heat Capacity of Workpiece, Density of Work Piece, Cutting Speed, Undeformed Chip Thickness & Average Temp Rise of Chip in Secondary Shear Zone and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Depth of Cut?

In this formula, Depth of Cut uses Rate of Heat Generation in Secondary Shear Zone, Specific Heat Capacity of Workpiece, Density of Work Piece, Cutting Speed, Undeformed Chip Thickness & Average Temp Rise of Chip in Secondary Shear Zone. We can use 1 other way(s) to calculate the same, which is/are as follows -

Depth of Cut = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Average Temperature Rise)

Home

FREE PDFs

🔍 Search