Density of Material using Average Temperature rise of Chip from Secondary Deformation Calculator

✖The Rate of Heat Generation in Secondary Shear Zone is the rate of heat generation in the area surrounding the chip tool contact region.ⓘ Rate of Heat Generation in Secondary Shear Zone [P_f]			+10% -10%
✖The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius.ⓘ Specific Heat Capacity of Workpiece [C]			+10% -10%
✖The Average Temp Rise of Chip in Secondary Shear Zone is defined as the amount of temperature rise in the secondary shear zone.ⓘ Average Temp Rise of Chip in Secondary Shear Zone [θ_f]			+10% -10%
✖Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).ⓘ Cutting Speed [V_cut]			+10% -10%
✖Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces.ⓘ Undeformed Chip Thickness [a_c]			+10% -10%
✖Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.ⓘ Depth of Cut [d_cut]			+10% -10%

✖Density of Work Piece From Secondary Deformation is the mass per unit volume ratio of the material of workpiece after secondary deformation.ⓘ Density of Material using Average Temperature rise of Chip from Secondary Deformation [ρ_sec]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Metal Machining Dynamics Formula PDF PDF Image

Density of Material using Average Temperature rise of Chip from Secondary Deformation Solution

STEP 0: Pre-Calculation Summary

Formula Used

Density of Work Piece From Secondary Deformation = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Average Temp Rise of Chip in Secondary Shear Zone*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)
ρ_sec = P_f/(C*θ_f*V_cut*a_c*d_cut)
This formula uses 7 Variables

Variables Used

Density of Work Piece From Secondary Deformation - (Measured in Kilogram per Cubic Meter) - Density of Work Piece From Secondary Deformation is the mass per unit volume ratio of the material of workpiece after secondary deformation.
Rate of Heat Generation in Secondary Shear Zone - (Measured in Watt) - The Rate of Heat Generation in Secondary Shear Zone is the rate of heat generation in the area surrounding the chip tool contact region.
Specific Heat Capacity of Workpiece - (Measured in Joule per Kilogram per K) - The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius.
Average Temp Rise of Chip in Secondary Shear Zone - (Measured in Kelvin) - The Average Temp Rise of Chip in Secondary Shear Zone is defined as the amount of temperature rise in the secondary shear zone.
Cutting Speed - (Measured in Meter per Second) - Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).
Undeformed Chip Thickness - (Measured in Meter) - Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces.
Depth of Cut - (Measured in Meter) - Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.

STEP 1: Convert Input(s) to Base Unit

Rate of Heat Generation in Secondary Shear Zone: 400 Watt --> 400 Watt No Conversion Required
Specific Heat Capacity of Workpiece: 502 Joule per Kilogram per K --> 502 Joule per Kilogram per K No Conversion Required
Average Temp Rise of Chip in Secondary Shear Zone: 88.5 Degree Celsius --> 88.5 Kelvin (Check conversion here)
Cutting Speed: 2 Meter per Second --> 2 Meter per Second No Conversion Required
Undeformed Chip Thickness: 0.25 Millimeter --> 0.00025 Meter (Check conversion here)
Depth of Cut: 2.5 Millimeter --> 0.0025 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

ρ_sec = P_f/(C*θ_f*V_cut*a_c*d_cut) --> 400/(502*88.5*2*0.00025*0.0025)

Evaluating ... ...

ρ_sec = 7202.82710964053

STEP 3: Convert Result to Output's Unit

7202.82710964053 Kilogram per Cubic Meter --> No Conversion Required

FINAL ANSWER

7202.82710964053 ≈ 7202.827 Kilogram per Cubic Meter <-- Density of Work Piece From Secondary Deformation

(Calculation completed in 00.011 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Metal Machining Dynamics » Temperatures in Metal Cutting » Temperature Rise » Density of Material using Average Temperature rise of Chip from Secondary Deformation

Credits

Created by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has created this Calculator and 300+ more calculators!

Verified by Kumar Siddhant

Indian Institute of Information Technology, Design and Manufacturing (IIITDM), Jabalpur

Kumar Siddhant has verified this Calculator and 100+ more calculators!

< Temperature Rise Calculators

Density of Material using Average Temperature Rise of material under Primary Shear Zone

LaTeX Go Density of Work Piece = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Average Temperature Rise*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Specific Heat given Average Temperature Rise of Material under Primary Shear Zone

LaTeX Go Specific Heat Capacity of Workpiece = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Average Temperature Rise*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Cutting Speed given Average Temperature Rise of Material under Primary Shear Zone

LaTeX Go Cutting Speed = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Average Temperature Rise*Undeformed Chip Thickness*Depth of Cut)

Average Temperature Rise of Material under Primary Deformation Zone

LaTeX Go Average Temperature Rise = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Density of Material using Average Temperature rise of Chip from Secondary Deformation Formula

LaTeX Go

What is density of workpiece?

Density is a measure of mass per volume. The average density of an object equals its total mass divided by its total volume. An object made from a comparatively dense material (such as iron) will have less volume than an object of equal mass made from some less dense substance (such as water).

How to Calculate Density of Material using Average Temperature rise of Chip from Secondary Deformation?

Density of Material using Average Temperature rise of Chip from Secondary Deformation calculator uses Density of Work Piece From Secondary Deformation = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Average Temp Rise of Chip in Secondary Shear Zone*Cutting Speed*Undeformed Chip Thickness*Depth of Cut) to calculate the Density of Work Piece From Secondary Deformation, The Density of material using Average Temperature rise of chip from Secondary Deformation is defined as the ratio of the mass of the chip formed per unit of the volume of the chip. Density of Work Piece From Secondary Deformation is denoted by ρ_sec symbol.

How to calculate Density of Material using Average Temperature rise of Chip from Secondary Deformation using this online calculator? To use this online calculator for Density of Material using Average Temperature rise of Chip from Secondary Deformation, enter Rate of Heat Generation in Secondary Shear Zone (P_f), Specific Heat Capacity of Workpiece (C), Average Temp Rise of Chip in Secondary Shear Zone (θ_f), Cutting Speed (V_cut), Undeformed Chip Thickness (a_c) & Depth of Cut (d_cut) and hit the calculate button. Here is how the Density of Material using Average Temperature rise of Chip from Secondary Deformation calculation can be explained with given input values -> 7202.827 = 400/(502*88.5*2*0.00025*0.0025).

FAQ

What is Density of Material using Average Temperature rise of Chip from Secondary Deformation?

The Density of material using Average Temperature rise of chip from Secondary Deformation is defined as the ratio of the mass of the chip formed per unit of the volume of the chip and is represented as ρ_sec = P_f/(C*θ_f*V_cut*a_c*d_cut) or Density of Work Piece From Secondary Deformation = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Average Temp Rise of Chip in Secondary Shear Zone*Cutting Speed*Undeformed Chip Thickness*Depth of Cut). The Rate of Heat Generation in Secondary Shear Zone is the rate of heat generation in the area surrounding the chip tool contact region, The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius, The Average Temp Rise of Chip in Secondary Shear Zone is defined as the amount of temperature rise in the secondary shear zone, Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute), Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces & Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.

How to calculate Density of Material using Average Temperature rise of Chip from Secondary Deformation?

The Density of material using Average Temperature rise of chip from Secondary Deformation is defined as the ratio of the mass of the chip formed per unit of the volume of the chip is calculated using Density of Work Piece From Secondary Deformation = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Average Temp Rise of Chip in Secondary Shear Zone*Cutting Speed*Undeformed Chip Thickness*Depth of Cut). To calculate Density of Material using Average Temperature rise of Chip from Secondary Deformation, you need Rate of Heat Generation in Secondary Shear Zone (P_f), Specific Heat Capacity of Workpiece (C), Average Temp Rise of Chip in Secondary Shear Zone (θ_f), Cutting Speed (V_cut), Undeformed Chip Thickness (a_c) & Depth of Cut (d_cut). With our tool, you need to enter the respective value for Rate of Heat Generation in Secondary Shear Zone, Specific Heat Capacity of Workpiece, Average Temp Rise of Chip in Secondary Shear Zone, Cutting Speed, Undeformed Chip Thickness & Depth of Cut and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search