Frequency of Cutting from Capacitance and Inductance Calculator

✖Inductance is the tendency of an electric conductor to oppose a change in the electric current flowing through it.ⓘ Inductance [L]			+10% -10%
✖Capacitance is the ratio of the amount of electric charge stored on a conductor to a difference in electric potential.ⓘ Capacitance [C]			+10% -10%

✖Frequency of Cutting refers to how often a machine or tool is engaged to trim, shape, or remove material from a workpiece during the production process.ⓘ Frequency of Cutting from Capacitance and Inductance [f_cut]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Unconventional machining processes Formula PDF PDF Image

Frequency of Cutting from Capacitance and Inductance Solution

STEP 0: Pre-Calculation Summary

Formula Used

Frequency of Cutting = 0.03/sqrt(Inductance*Capacitance)
f_cut = 0.03/sqrt(L*C)
This formula uses 1 Functions, 3 Variables

Functions Used

sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Frequency of Cutting - (Measured in Hertz) - Frequency of Cutting refers to how often a machine or tool is engaged to trim, shape, or remove material from a workpiece during the production process.
Inductance - (Measured in Henry) - Inductance is the tendency of an electric conductor to oppose a change in the electric current flowing through it.
Capacitance - (Measured in Farad) - Capacitance is the ratio of the amount of electric charge stored on a conductor to a difference in electric potential.

STEP 1: Convert Input(s) to Base Unit

Inductance: 5.7 Henry --> 5.7 Henry No Conversion Required
Capacitance: 6.3 Farad --> 6.3 Farad No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

f_cut = 0.03/sqrt(L*C) --> 0.03/sqrt(5.7*6.3)

Evaluating ... ...

f_cut = 0.00500626174321759

STEP 3: Convert Result to Output's Unit

0.00500626174321759 Hertz -->0.00500626174321759 Cycle per Second (Check conversion here)

FINAL ANSWER

0.00500626174321759 ≈ 0.005006 Cycle per Second <-- Frequency of Cutting

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » System Analysis in EDM » Relaxation Circuit used for Generating Pulses in EDM » Frequency of Cutting » Frequency of Cutting from Capacitance and Inductance

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Vaibhav Malani

National Institute of Technology (NIT), Tiruchirapalli

Vaibhav Malani has verified this Calculator and 200+ more calculators!

< Frequency of Cutting Calculators

Frequency of Cutting from Capacitance and Inductance

LaTeX Go Frequency of Cutting = 0.03/sqrt(Inductance*Capacitance)

Frequency of Cutting using Charging and Sparking Time

LaTeX Go Frequency of Cutting = 1/(Sparking Time+Charging Time)

Sparking Time from Frequency of Cutting

LaTeX Go Sparking Time = 1/Frequency of Cutting-Charging Time

Charging Time from Cutting Frequency

LaTeX Go Charging Time = 1/Frequency of Cutting-Sparking Time

Frequency of Cutting from Capacitance and Inductance Formula

LaTeX Go

Frequency of Cutting = 0.03/sqrt(Inductance*Capacitance)
f_cut = 0.03/sqrt(L*C)

How the spark is produced in Electric Discharge Machining ?

A typical circuit used for supplying the power to an EDM machine is named as the relaxation circuit. The circuit consists of a DC power source, which charges the capacitor ‘C’ across a resistance ‘Rc’. Initially when the capacitor is in the uncharged condition, when the power supply is on with a voltage of Vo, a heavy current, ic, will flow in the circuit as shown to charge the capacitor.The relaxation circuit as explained above was used in the early EDM machines. They are limited to the low material removal rates for fine finish, which limits its application. This can be explained from the fact that the time spent on charging the capacitor is quite large during which time, no machining can actually take place. Thus the material removal rates are low.

How to Calculate Frequency of Cutting from Capacitance and Inductance?

Frequency of Cutting from Capacitance and Inductance calculator uses Frequency of Cutting = 0.03/sqrt(Inductance*Capacitance) to calculate the Frequency of Cutting, The Frequency of cutting from capacitance and inductance formula is defined as the inverse of the sum of charging time and sparking time. Frequency of Cutting is denoted by f_cut symbol.

How to calculate Frequency of Cutting from Capacitance and Inductance using this online calculator? To use this online calculator for Frequency of Cutting from Capacitance and Inductance, enter Inductance (L) & Capacitance (C) and hit the calculate button. Here is how the Frequency of Cutting from Capacitance and Inductance calculation can be explained with given input values -> 0.005006 = 0.03/sqrt(5.7*6.3).

FAQ

What is Frequency of Cutting from Capacitance and Inductance?

The Frequency of cutting from capacitance and inductance formula is defined as the inverse of the sum of charging time and sparking time and is represented as f_cut = 0.03/sqrt(L*C) or Frequency of Cutting = 0.03/sqrt(Inductance*Capacitance). Inductance is the tendency of an electric conductor to oppose a change in the electric current flowing through it & Capacitance is the ratio of the amount of electric charge stored on a conductor to a difference in electric potential.

How to calculate Frequency of Cutting from Capacitance and Inductance?

The Frequency of cutting from capacitance and inductance formula is defined as the inverse of the sum of charging time and sparking time is calculated using Frequency of Cutting = 0.03/sqrt(Inductance*Capacitance). To calculate Frequency of Cutting from Capacitance and Inductance, you need Inductance (L) & Capacitance (C). With our tool, you need to enter the respective value for Inductance & Capacitance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Frequency of Cutting?

In this formula, Frequency of Cutting uses Inductance & Capacitance. We can use 1 other way(s) to calculate the same, which is/are as follows -

Frequency of Cutting = 1/(Sparking Time+Charging Time)

Home

FREE PDFs

🔍 Search