Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone Calculator

✖Fraction of Heat Conducted into The Workpiece defined as a portion of specimen which is conducted to the workpiece, so, this portion will not cause a temperature increase in the chip.ⓘ Fraction of Heat Conducted into The Workpiece [Γ]			+10% -10%
✖The Rate of Heat Generation in Primary Shear Zone is the heat transfer rate in the narrow zone surrounding the shear plane in machining.ⓘ Rate of Heat Generation in Primary Shear Zone [P_s]			+10% -10%
✖Density of Work Piece is the mass per unit volume ratio of the material of workpiece.ⓘ Density of Work Piece [ρ_wp]			+10% -10%
✖The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius.ⓘ Specific Heat Capacity of Workpiece [C]			+10% -10%
✖Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).ⓘ Cutting Speed [V_cut]			+10% -10%
✖Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces.ⓘ Undeformed Chip Thickness [a_c]			+10% -10%
✖Average Temperature Rise is defined as the actual amount of increase in the temperature.ⓘ Average Temperature Rise [θ_avg]			+10% -10%

✖Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.ⓘ Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone [d_cut]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Production Engineering Formula PDF PDF Image

Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone Solution

STEP 0: Pre-Calculation Summary

Formula Used

Depth of Cut = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Average Temperature Rise)
d_cut = ((1-Γ)*P_s)/(ρ_wp*C*V_cut*a_c*θ_avg)
This formula uses 8 Variables

Variables Used

Depth of Cut - (Measured in Meter) - Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.
Fraction of Heat Conducted into The Workpiece - Fraction of Heat Conducted into The Workpiece defined as a portion of specimen which is conducted to the workpiece, so, this portion will not cause a temperature increase in the chip.
Rate of Heat Generation in Primary Shear Zone - (Measured in Watt) - The Rate of Heat Generation in Primary Shear Zone is the heat transfer rate in the narrow zone surrounding the shear plane in machining.
Density of Work Piece - (Measured in Kilogram per Cubic Meter) - Density of Work Piece is the mass per unit volume ratio of the material of workpiece.
Specific Heat Capacity of Workpiece - (Measured in Joule per Kilogram per K) - The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius.
Cutting Speed - (Measured in Meter per Second) - Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).
Undeformed Chip Thickness - (Measured in Meter) - Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces.
Average Temperature Rise - (Measured in Kelvin) - Average Temperature Rise is defined as the actual amount of increase in the temperature.

STEP 1: Convert Input(s) to Base Unit

Fraction of Heat Conducted into The Workpiece: 0.1 --> No Conversion Required
Rate of Heat Generation in Primary Shear Zone: 1380 Watt --> 1380 Watt No Conversion Required
Density of Work Piece: 7200 Kilogram per Cubic Meter --> 7200 Kilogram per Cubic Meter No Conversion Required
Specific Heat Capacity of Workpiece: 502 Joule per Kilogram per K --> 502 Joule per Kilogram per K No Conversion Required
Cutting Speed: 2 Meter per Second --> 2 Meter per Second No Conversion Required
Undeformed Chip Thickness: 0.25 Millimeter --> 0.00025 Meter (Check conversion here)
Average Temperature Rise: 274.9 Degree Celsius --> 274.9 Kelvin (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

d_cut = ((1-Γ)*P_s)/(ρ_wp*C*V_cut*a_c*θ_avg) --> ((1-0.1)*1380)/(7200*502*2*0.00025*274.9)

Evaluating ... ...

d_cut = 0.00250000362319366

STEP 3: Convert Result to Output's Unit

0.00250000362319366 Meter -->2.50000362319366 Millimeter (Check conversion here)

FINAL ANSWER

2.50000362319366 ≈ 2.500004 Millimeter <-- Depth of Cut

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Metal Machining Dynamics » Temperatures in Metal Cutting » Temperature Rise » Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone

Credits

Created by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has created this Calculator and 300+ more calculators!

Verified by Kumar Siddhant

Indian Institute of Information Technology, Design and Manufacturing (IIITDM), Jabalpur

Kumar Siddhant has verified this Calculator and 100+ more calculators!

< Temperature Rise Calculators

Density of Material using Average Temperature Rise of material under Primary Shear Zone

LaTeX Go Density of Work Piece = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Average Temperature Rise*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Specific Heat given Average Temperature Rise of Material under Primary Shear Zone

LaTeX Go Specific Heat Capacity of Workpiece = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Average Temperature Rise*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Cutting Speed given Average Temperature Rise of Material under Primary Shear Zone

LaTeX Go Cutting Speed = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Average Temperature Rise*Undeformed Chip Thickness*Depth of Cut)

Average Temperature Rise of Material under Primary Deformation Zone

LaTeX Go Average Temperature Rise = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)

Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone Formula

LaTeX Go

What is Depth of Cut?

It is the total amount of metal removed per pass of the cutting tool. It is expressed in mm. It can vary and depend upon the type of tool and work material.

How to Calculate Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone?

Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone calculator uses Depth of Cut = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Average Temperature Rise) to calculate the Depth of Cut, The Depth of cut given Average Temperature rise of material under Primary Shear Zone is the total amount of metal removed per pass of the cutting tool. Depth of Cut is denoted by d_cut symbol.

How to calculate Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone using this online calculator? To use this online calculator for Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone, enter Fraction of Heat Conducted into The Workpiece (Γ), Rate of Heat Generation in Primary Shear Zone (P_s), Density of Work Piece (ρ_wp), Specific Heat Capacity of Workpiece (C), Cutting Speed (V_cut), Undeformed Chip Thickness (a_c) & Average Temperature Rise (θ_avg) and hit the calculate button. Here is how the Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone calculation can be explained with given input values -> 2499.022 = ((1-0.1)*1380)/(7200*502*2*0.00025*274.9).

FAQ

What is Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone?

The Depth of cut given Average Temperature rise of material under Primary Shear Zone is the total amount of metal removed per pass of the cutting tool and is represented as d_cut = ((1-Γ)*P_s)/(ρ_wp*C*V_cut*a_c*θ_avg) or Depth of Cut = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Average Temperature Rise). Fraction of Heat Conducted into The Workpiece defined as a portion of specimen which is conducted to the workpiece, so, this portion will not cause a temperature increase in the chip, The Rate of Heat Generation in Primary Shear Zone is the heat transfer rate in the narrow zone surrounding the shear plane in machining, Density of Work Piece is the mass per unit volume ratio of the material of workpiece, The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius, Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute), Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces & Average Temperature Rise is defined as the actual amount of increase in the temperature.

How to calculate Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone?

The Depth of cut given Average Temperature rise of material under Primary Shear Zone is the total amount of metal removed per pass of the cutting tool is calculated using Depth of Cut = ((1-Fraction of Heat Conducted into The Workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of Work Piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Average Temperature Rise). To calculate Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone, you need Fraction of Heat Conducted into The Workpiece (Γ), Rate of Heat Generation in Primary Shear Zone (P_s), Density of Work Piece (ρ_wp), Specific Heat Capacity of Workpiece (C), Cutting Speed (V_cut), Undeformed Chip Thickness (a_c) & Average Temperature Rise (θ_avg). With our tool, you need to enter the respective value for Fraction of Heat Conducted into The Workpiece, Rate of Heat Generation in Primary Shear Zone, Density of Work Piece, Specific Heat Capacity of Workpiece, Cutting Speed, Undeformed Chip Thickness & Average Temperature Rise and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Depth of Cut?

In this formula, Depth of Cut uses Fraction of Heat Conducted into The Workpiece, Rate of Heat Generation in Primary Shear Zone, Density of Work Piece, Specific Heat Capacity of Workpiece, Cutting Speed, Undeformed Chip Thickness & Average Temperature Rise. We can use 1 other way(s) to calculate the same, which is/are as follows -

Depth of Cut = Rate of Heat Generation in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of Work Piece*Cutting Speed*Undeformed Chip Thickness*Average Temp Rise of Chip in Secondary Shear Zone)

Home

FREE PDFs

🔍 Search