Endurance Limit of Specimen Calculator

✖The Surface Finish Factor takes into account the reduction in endurance limit due to variation in the surface finish between the specimen and the actual component.ⓘ Surface Finish Factor [K_a]			+10% -10%
✖The Size Factor takes into account the reduction in endurance limit due to an increase in the size of the component.ⓘ Size Factor [K_b]			+10% -10%
✖Reliabilty Factor accounts for the reliability that is used in the design of the component.ⓘ Reliabilty Factor [K_c]			+10% -10%
✖The Modifying Factor for Stress Concentration accounts for the effect of stress concentration on a specimen for cyclic loading.ⓘ Modifying Factor for Stress Concentration [K_d]			+10% -10%
✖Endurance Limit of Rotating Beam Specimen is the maximum value of the completely reversed stress for which the specimen can sustain for an infinite number of cycles without any fatigue failure.ⓘ Endurance Limit of Rotating Beam Specimen [S'_e]			+10% -10%

✖The Endurance Limit of a material is defined as the stress below which a material can endure an infinite number of repeated load cycles without exhibiting failure.ⓘ Endurance Limit of Specimen [S_e]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Design against Fluctuating Load Formula PDF PDF Image

Endurance Limit of Specimen Solution

STEP 0: Pre-Calculation Summary

Formula Used

Endurance Limit = Surface Finish Factor*Size Factor*Reliabilty Factor*Modifying Factor for Stress Concentration*Endurance Limit of Rotating Beam Specimen
S_e = K_a*K_b*K_c*K_d*S'_e
This formula uses 6 Variables

Variables Used

Endurance Limit - (Measured in Pascal) - The Endurance Limit of a material is defined as the stress below which a material can endure an infinite number of repeated load cycles without exhibiting failure.
Surface Finish Factor - The Surface Finish Factor takes into account the reduction in endurance limit due to variation in the surface finish between the specimen and the actual component.
Size Factor - The Size Factor takes into account the reduction in endurance limit due to an increase in the size of the component.
Reliabilty Factor - Reliabilty Factor accounts for the reliability that is used in the design of the component.
Modifying Factor for Stress Concentration - The Modifying Factor for Stress Concentration accounts for the effect of stress concentration on a specimen for cyclic loading.
Endurance Limit of Rotating Beam Specimen - (Measured in Pascal) - Endurance Limit of Rotating Beam Specimen is the maximum value of the completely reversed stress for which the specimen can sustain for an infinite number of cycles without any fatigue failure.

STEP 1: Convert Input(s) to Base Unit

Surface Finish Factor: 0.92 --> No Conversion Required
Size Factor: 0.85 --> No Conversion Required
Reliabilty Factor: 0.89 --> No Conversion Required
Modifying Factor for Stress Concentration: 0.34 --> No Conversion Required
Endurance Limit of Rotating Beam Specimen: 220 Newton per Square Millimeter --> 220000000 Pascal (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

S_e = K_a*K_b*K_c*K_d*S'_e --> 0.92*0.85*0.89*0.34*220000000

Evaluating ... ...

S_e = 52059304

STEP 3: Convert Result to Output's Unit

52059304 Pascal -->52.059304 Newton per Square Millimeter (Check conversion here)

FINAL ANSWER

52.059304 ≈ 52.0593 Newton per Square Millimeter <-- Endurance Limit

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Mechanical » Machine Design » Design against Fluctuating Load » Endurance Limit Approximate Estimation in Design » Endurance Limit of Specimen

Credits

Created by Vaibhav Malani

National Institute of Technology (NIT), Tiruchirapalli

Vaibhav Malani has created this Calculator and 600+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Endurance Limit Approximate Estimation in Design Calculators

Stress Amplitude for Fluctuating load given Maximum Stress and Minimum Stress

LaTeX Go Stress Amplitude for Fluctuating Load = (Maximum Stress Value for Fluctuating Load-Minimum Stress Value for Fluctuating Load)/2

Endurance Limit of Rotating Beam Specimen of Steel

LaTeX Go Endurance Limit of Rotating Beam Specimen = 0.5*Ultimate Tensile strength

Endurance Limit Stress of Rotating Beam Specimen of Cast Iron or Steels

LaTeX Go Endurance Limit Stress = 0.4*Ultimate Tensile strength

Endurance Limit Stress of Rotating Beam Specimen of Aluminium Alloys

LaTeX Go Endurance Limit Stress = 0.4*Ultimate Tensile strength

Endurance Limit of Specimen Formula

LaTeX Go

Endurance Limit = Surface Finish Factor*Size Factor*Reliabilty Factor*Modifying Factor for Stress Concentration*Endurance Limit of Rotating Beam Specimen
S_e = K_a*K_b*K_c*K_d*S'_e

What is Endurance Limit?

The fatigue or endurance limit of a material is defined as the maximum amplitude of completely reversed stress that the standard specimen can sustain for an unlimited number of cycles without fatigue failure.

How to Calculate Endurance Limit of Specimen?

Endurance Limit of Specimen calculator uses Endurance Limit = Surface Finish Factor*Size Factor*Reliabilty Factor*Modifying Factor for Stress Concentration*Endurance Limit of Rotating Beam Specimen to calculate the Endurance Limit, Endurance Limit of Specimen formula is defined as a measure of a material's ability to withstand repeated loading and unloading without failure, providing a critical value for machine design and structural integrity. Endurance Limit is denoted by S_e symbol.

How to calculate Endurance Limit of Specimen using this online calculator? To use this online calculator for Endurance Limit of Specimen, enter Surface Finish Factor (K_a), Size Factor (K_b), Reliabilty Factor (K_c), Modifying Factor for Stress Concentration (K_d) & Endurance Limit of Rotating Beam Specimen (S'_e) and hit the calculate button. Here is how the Endurance Limit of Specimen calculation can be explained with given input values -> 5.2E-5 = 0.92*0.85*0.89*0.34*220000000.

FAQ

What is Endurance Limit of Specimen?

Endurance Limit of Specimen formula is defined as a measure of a material's ability to withstand repeated loading and unloading without failure, providing a critical value for machine design and structural integrity and is represented as S_e = K_a*K_b*K_c*K_d*S'_e or Endurance Limit = Surface Finish Factor*Size Factor*Reliabilty Factor*Modifying Factor for Stress Concentration*Endurance Limit of Rotating Beam Specimen. The Surface Finish Factor takes into account the reduction in endurance limit due to variation in the surface finish between the specimen and the actual component, The Size Factor takes into account the reduction in endurance limit due to an increase in the size of the component, Reliabilty Factor accounts for the reliability that is used in the design of the component, The Modifying Factor for Stress Concentration accounts for the effect of stress concentration on a specimen for cyclic loading & Endurance Limit of Rotating Beam Specimen is the maximum value of the completely reversed stress for which the specimen can sustain for an infinite number of cycles without any fatigue failure.

How to calculate Endurance Limit of Specimen?

Endurance Limit of Specimen formula is defined as a measure of a material's ability to withstand repeated loading and unloading without failure, providing a critical value for machine design and structural integrity is calculated using Endurance Limit = Surface Finish Factor*Size Factor*Reliabilty Factor*Modifying Factor for Stress Concentration*Endurance Limit of Rotating Beam Specimen. To calculate Endurance Limit of Specimen, you need Surface Finish Factor (K_a), Size Factor (K_b), Reliabilty Factor (K_c), Modifying Factor for Stress Concentration (K_d) & Endurance Limit of Rotating Beam Specimen (S'_e). With our tool, you need to enter the respective value for Surface Finish Factor, Size Factor, Reliabilty Factor, Modifying Factor for Stress Concentration & Endurance Limit of Rotating Beam Specimen and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Endurance Limit?

In this formula, Endurance Limit uses Surface Finish Factor, Size Factor, Reliabilty Factor, Modifying Factor for Stress Concentration & Endurance Limit of Rotating Beam Specimen. We can use 1 other way(s) to calculate the same, which is/are as follows -

Endurance Limit = Endurance Limit for Axial Loading/0.8

Home

FREE PDFs

🔍 Search