Drain Current of Class B Amplifier Calculator

✖Output Current is calculated by the current obtained in the single ended class-B amplifier.ⓘ Output Current [I_out]

+10%

-10%

✖Drain Current is the current carrying capacity of the silicon chip and which is used as a reference for comparing with other products.ⓘ Drain Current of Class B Amplifier [I_d]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Output Stages and Power Amplifiers Formulas PDF PDF Image

Drain Current of Class B Amplifier Solution

STEP 0: Pre-Calculation Summary

Formula Used

Drain Current = 2*(Output Current/pi)
I_d = 2*(I_out/pi)
This formula uses 1 Constants, 2 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Drain Current - (Measured in Ampere) - Drain Current is the current carrying capacity of the silicon chip and which is used as a reference for comparing with other products.
Output Current - (Measured in Ampere) - Output Current is calculated by the current obtained in the single ended class-B amplifier.

STEP 1: Convert Input(s) to Base Unit

Output Current: 0.023 Milliampere --> 2.3E-05 Ampere (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

I_d = 2*(I_out/pi) --> 2*(2.3E-05/pi)

Evaluating ... ...

I_d = 1.46422547644544E-05

STEP 3: Convert Result to Output's Unit

1.46422547644544E-05 Ampere -->0.0146422547644544 Milliampere (Check conversion here)

FINAL ANSWER

0.0146422547644544 ≈ 0.014642 Milliampere <-- Drain Current

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics » Amplifiers » Output Stages and Power Amplifiers » Class A Output Stage » Drain Current of Class B Amplifier

Credits

Created by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has created this Calculator and 600+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Class A Output Stage Calculators

Bias Current of Emitter Follower

LaTeX Go Input Bias Current = modulus((-Supply Voltage)+Saturation Voltage 2)/Load Resistance

Saturation Voltage between Collector-Emitter at Transistor 1

LaTeX Go Saturation Voltage 1 = Supply Voltage-Maximum Voltage

Saturation Voltage between Collector-Emitter at Transistor 2

LaTeX Go Saturation Voltage 2 = Minimum Voltage+Supply Voltage

Load Voltage

LaTeX Go Load Voltage = Input Voltage-Base Emitter Voltage

Drain Current of Class B Amplifier Formula

LaTeX Go

Drain Current = 2*(Output Current/pi)
I_d = 2*(I_out/pi)

What is class A output stage? Where are class A amplifiers used?

A Class A amplifier stage passes the same load current even when no input signal is applied so large heatsinks are needed for the output transistors. These types of devices are basically two transistors within a single package, one small “pilot” transistor and another larger “switching” transistor.

The Class A Amplifier more suitable for outdoor musical systems, since the transistor reproduces the entire audio waveform without ever cutting off. As a result, the sound is very clear and more linear, that is, it contains much lower levels of distortion.

How to Calculate Drain Current of Class B Amplifier?

Drain Current of Class B Amplifier calculator uses Drain Current = 2*(Output Current/pi) to calculate the Drain Current, Drain Current of Class B Amplifier is the current carrying capacity of the silicon chip and which is used as a reference for comparing with other products. Drain Current is denoted by I_d symbol.

How to calculate Drain Current of Class B Amplifier using this online calculator? To use this online calculator for Drain Current of Class B Amplifier, enter Output Current (I_out) and hit the calculate button. Here is how the Drain Current of Class B Amplifier calculation can be explained with given input values -> 14.64225 = 2*(2.3E-05/pi).

FAQ

What is Drain Current of Class B Amplifier?

Drain Current of Class B Amplifier is the current carrying capacity of the silicon chip and which is used as a reference for comparing with other products and is represented as I_d = 2*(I_out/pi) or Drain Current = 2*(Output Current/pi). Output Current is calculated by the current obtained in the single ended class-B amplifier.

How to calculate Drain Current of Class B Amplifier?

Drain Current of Class B Amplifier is the current carrying capacity of the silicon chip and which is used as a reference for comparing with other products is calculated using Drain Current = 2*(Output Current/pi). To calculate Drain Current of Class B Amplifier, you need Output Current (I_out). With our tool, you need to enter the respective value for Output Current and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search