Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin Calculator

✖Force on Roller Pin is the force acting onto the roller pin ( the pivot about which a lever rolls freely) used as a joint.ⓘ Force on Roller Pin [P_c]			+10% -10%
✖Shear Stress in Roller Pin is the shear stress-induced into the pin, the force per unit area tending to cause deformation of the pin by slippage along a plane or planes parallel to the imposed stress.ⓘ Shear Stress in Roller Pin [τ_r]			+10% -10%

✖Diameter of Roller Pin is the diameter of the pin used at the roller joint.ⓘ Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin [d₂]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download IC Engine Formula PDF PDF Image

Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin Solution

STEP 0: Pre-Calculation Summary

Formula Used

Diameter of Roller Pin = sqrt((2*Force on Roller Pin)/(pi*Shear Stress in Roller Pin))
d₂ = sqrt((2*P_c)/(pi*τ_r))
This formula uses 1 Constants, 1 Functions, 3 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Functions Used

sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Diameter of Roller Pin - (Measured in Meter) - Diameter of Roller Pin is the diameter of the pin used at the roller joint.
Force on Roller Pin - (Measured in Newton) - Force on Roller Pin is the force acting onto the roller pin ( the pivot about which a lever rolls freely) used as a joint.
Shear Stress in Roller Pin - (Measured in Pascal) - Shear Stress in Roller Pin is the shear stress-induced into the pin, the force per unit area tending to cause deformation of the pin by slippage along a plane or planes parallel to the imposed stress.

STEP 1: Convert Input(s) to Base Unit

Force on Roller Pin: 1925 Newton --> 1925 Newton No Conversion Required
Shear Stress in Roller Pin: 2.8 Newton per Square Millimeter --> 2800000 Pascal (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

d₂ = sqrt((2*P_c)/(pi*τ_r)) --> sqrt((2*1925)/(pi*2800000))

Evaluating ... ...

d₂ = 0.02092070967971

STEP 3: Convert Result to Output's Unit

0.02092070967971 Meter -->20.92070967971 Millimeter (Check conversion here)

FINAL ANSWER

20.92070967971 ≈ 20.92071 Millimeter <-- Diameter of Roller Pin

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » IC Engine » Design of IC Engine Components » Rocker Arm » Mechanical » Design of Forked End » Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin

Credits

Created by Saurabh Patil

Shri Govindram Seksaria Institute of Technology and Science (SGSITS ), Indore

Saurabh Patil has created this Calculator and 700+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Design of Forked End Calculators

Length of Roller Pin of Forked End of Rocker Arm

LaTeX Go Length of Roller Pin = 1.25*(Force on Roller Pin)/(Bearing Pressure for Roller Pin*Diameter of Roller Pin)

Bearing Pressure at Roller Pin of Forked End of Rocker Arm

LaTeX Go Bearing Pressure for Roller Pin = (Force on Roller Pin)/(Diameter of Roller Pin*Length of Roller Pin)

Diameter of Roller Pin at Forked End of Rocker Arm

LaTeX Go Diameter of Roller Pin = (Force on Roller Pin)/(Bearing Pressure for Roller Pin*Length of Roller Pin)

Force on Roller Pin of Forked End of Rocker Arm

LaTeX Go Force on Roller Pin = Bearing Pressure for Roller Pin*Diameter of Roller Pin*Length of Roller Pin

Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin Formula

LaTeX Go

Diameter of Roller Pin = sqrt((2*Force on Roller Pin)/(pi*Shear Stress in Roller Pin))
d₂ = sqrt((2*P_c)/(pi*τ_r))

What is Rocker ratio?

The rocker ratio is the distance traveled by the valve divided by the distance traveled by the pushrod effective. The ratio is determined by the ratio of the distances from the rocker arm's pivot point to the point where it touches the valve and the point where it touches the pushrod/camshaft. A rocker ratio greater than one essentially increases the camshaft's lift.
Current automotive design favors rocker arm ratios of about 1.5:1 to 1.8:1. However, in the past smaller positive ratios have been used, including a 1:1 (neutral ratio) in many engines prior to the 1950s, and ratios less than 1 (valve lift smaller than the cam lift) have also been used at times.

How to Calculate Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin?

Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin calculator uses Diameter of Roller Pin = sqrt((2*Force on Roller Pin)/(pi*Shear Stress in Roller Pin)) to calculate the Diameter of Roller Pin, The Diameter of roller pin of forked end of rocker arm considering double shear failure of pin is the diameter of the roller pin used at the roller joint of the rocker arm at its forked end. Diameter of Roller Pin is denoted by d₂ symbol.

How to calculate Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin using this online calculator? To use this online calculator for Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin, enter Force on Roller Pin (P_c) & Shear Stress in Roller Pin (τ_r) and hit the calculate button. Here is how the Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin calculation can be explained with given input values -> 20920.71 = sqrt((2*1925)/(pi*2800000)).

FAQ

What is Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin?

The Diameter of roller pin of forked end of rocker arm considering double shear failure of pin is the diameter of the roller pin used at the roller joint of the rocker arm at its forked end and is represented as d₂ = sqrt((2*P_c)/(pi*τ_r)) or Diameter of Roller Pin = sqrt((2*Force on Roller Pin)/(pi*Shear Stress in Roller Pin)). Force on Roller Pin is the force acting onto the roller pin ( the pivot about which a lever rolls freely) used as a joint & Shear Stress in Roller Pin is the shear stress-induced into the pin, the force per unit area tending to cause deformation of the pin by slippage along a plane or planes parallel to the imposed stress.

How to calculate Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin?

The Diameter of roller pin of forked end of rocker arm considering double shear failure of pin is the diameter of the roller pin used at the roller joint of the rocker arm at its forked end is calculated using Diameter of Roller Pin = sqrt((2*Force on Roller Pin)/(pi*Shear Stress in Roller Pin)). To calculate Diameter of Roller Pin of Forked End of Rocker Arm Considering Double Shear Failure of Pin, you need Force on Roller Pin (P_c) & Shear Stress in Roller Pin (τ_r). With our tool, you need to enter the respective value for Force on Roller Pin & Shear Stress in Roller Pin and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Diameter of Roller Pin?

In this formula, Diameter of Roller Pin uses Force on Roller Pin & Shear Stress in Roller Pin. We can use 3 other way(s) to calculate the same, which is/are as follows -

Diameter of Roller Pin = (Force on Roller Pin)/(Bearing Pressure for Roller Pin*Length of Roller Pin)
Diameter of Roller Pin = Length of Roller Pin/1.25
Diameter of Roller Pin = (2*Bearing Pressure for Roller Pin*Length of Roller Pin)/(pi*Shear Stress in Roller Pin)

Home

FREE PDFs

🔍 Search