Diameter of rivet given tearing strength of rivet Calculator

✖Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member.ⓘ Pitch of Rivet [p]			+10% -10%
✖Strength of Tearing is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions.ⓘ Strength of Tearing [T_str]			+10% -10%
✖Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force.ⓘ Tensile Stress [σ_t]			+10% -10%
✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of Plate [t_plate]			+10% -10%

✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Diameter of rivet given tearing strength of rivet [D_rivet]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Diameter of rivet given tearing strength of rivet Solution

STEP 0: Pre-Calculation Summary

Formula Used

Rivet Diameter = Pitch of Rivet-(Strength of Tearing/(Tensile Stress*Thickness of Plate))
D_rivet = p-(T_str/(σ_t*t_plate))
This formula uses 5 Variables

Variables Used

Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
Pitch of Rivet - (Measured in Meter) - Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member.
Strength of Tearing - (Measured in Newton) - Strength of Tearing is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions.
Tensile Stress - (Measured in Pascal) - Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

STEP 1: Convert Input(s) to Base Unit

Pitch of Rivet: 20 Millimeter --> 0.02 Meter (Check conversion here)
Strength of Tearing: 0.015 Kilonewton --> 15 Newton (Check conversion here)
Tensile Stress: 0.173 Megapascal --> 173000 Pascal (Check conversion here)
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

D_rivet = p-(T_str/(σ_t*t_plate)) --> 0.02-(15/(173000*0.012))

Evaluating ... ...

D_rivet = 0.0127745664739884

STEP 3: Convert Result to Output's Unit

0.0127745664739884 Meter -->12.7745664739884 Millimeter (Check conversion here)

FINAL ANSWER

12.7745664739884 ≈ 12.77457 Millimeter <-- Rivet Diameter

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Strength of a Riveted Joint » Mechanical » Diameter of Rivet » Diameter of rivet given tearing strength of rivet

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Diameter of Rivet Calculators

Diameter of rivet given crushing strength for 'n' number of rivets

LaTeX Go Rivet Diameter = Crushing strength/(Number of Rivets Per Pitch*Crushing Stress*Thickness of Plate)

Diameter of rivet given crushing strength for double rivet

LaTeX Go Rivet Diameter = Crushing strength/(2*Crushing Stress*Thickness of Plate)

Diameter of rivet given crushing strength for single rivet

LaTeX Go Rivet Diameter = Crushing strength/(1*Crushing Stress*Thickness of Plate)

Diameter of rivet given crushing strength for triple-rivet

LaTeX Go Rivet Diameter = Crushing strength/(3*Crushing Stress*Thickness of Plate)

Diameter of rivet given tearing strength of rivet Formula

LaTeX Go

Rivet Diameter = Pitch of Rivet-(Strength of Tearing/(Tensile Stress*Thickness of Plate))
D_rivet = p-(T_str/(σ_t*t_plate))

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Diameter of rivet given tearing strength of rivet?

Diameter of rivet given tearing strength of rivet calculator uses Rivet Diameter = Pitch of Rivet-(Strength of Tearing/(Tensile Stress*Thickness of Plate)) to calculate the Rivet Diameter, The Diameter of rivet given tearing strength of rivet formula is defined as a chord that runs through the center point of the rivet. Rivet Diameter is denoted by D_rivet symbol.

How to calculate Diameter of rivet given tearing strength of rivet using this online calculator? To use this online calculator for Diameter of rivet given tearing strength of rivet, enter Pitch of Rivet (p), Strength of Tearing (T_str), Tensile Stress (σ_t) & Thickness of Plate (t_plate) and hit the calculate button. Here is how the Diameter of rivet given tearing strength of rivet calculation can be explained with given input values -> 12774.57 = 0.02-(15/(173000*0.012)).

FAQ

What is Diameter of rivet given tearing strength of rivet?

The Diameter of rivet given tearing strength of rivet formula is defined as a chord that runs through the center point of the rivet and is represented as D_rivet = p-(T_str/(σ_t*t_plate)) or Rivet Diameter = Pitch of Rivet-(Strength of Tearing/(Tensile Stress*Thickness of Plate)). Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member, Strength of Tearing is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions, Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force & The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

How to calculate Diameter of rivet given tearing strength of rivet?

The Diameter of rivet given tearing strength of rivet formula is defined as a chord that runs through the center point of the rivet is calculated using Rivet Diameter = Pitch of Rivet-(Strength of Tearing/(Tensile Stress*Thickness of Plate)). To calculate Diameter of rivet given tearing strength of rivet, you need Pitch of Rivet (p), Strength of Tearing (T_str), Tensile Stress (σ_t) & Thickness of Plate (t_plate). With our tool, you need to enter the respective value for Pitch of Rivet, Strength of Tearing, Tensile Stress & Thickness of Plate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Rivet Diameter?

In this formula, Rivet Diameter uses Pitch of Rivet, Strength of Tearing, Tensile Stress & Thickness of Plate. We can use 3 other way(s) to calculate the same, which is/are as follows -

Rivet Diameter = Crushing strength/(2*Crushing Stress*Thickness of Plate)
Rivet Diameter = Crushing strength/(Number of Rivets Per Pitch*Crushing Stress*Thickness of Plate)
Rivet Diameter = Crushing strength/(1*Crushing Stress*Thickness of Plate)

Home

FREE PDFs

🔍 Search