Diameter of rivet given strength of joint per pitch length (single rivet) Calculator

✖Strength of joint is the strength of riveted joint per pitch length.ⓘ Strength of Joint [S]			+10% -10%
✖Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.ⓘ Crushing Stress [σ_c]			+10% -10%
✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of Plate [t_plate]			+10% -10%

✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Diameter of rivet given strength of joint per pitch length (single rivet) [D_rivet]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Diameter of rivet given strength of joint per pitch length (single rivet) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Rivet Diameter = Strength of Joint/(1*Crushing Stress*Thickness of Plate)
D_rivet = S/(1*σ_c*t_plate)
This formula uses 4 Variables

Variables Used

Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
Strength of Joint - (Measured in Newton) - Strength of joint is the strength of riveted joint per pitch length.
Crushing Stress - (Measured in Pascal) - Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

STEP 1: Convert Input(s) to Base Unit

Strength of Joint: 8.6 Kilonewton --> 8600 Newton (Check conversion here)
Crushing Stress: 20.83333 Megapascal --> 20833330 Pascal (Check conversion here)
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

D_rivet = S/(1*σ_c*t_plate) --> 8600/(1*20833330*0.012)

Evaluating ... ...

D_rivet = 0.0344000055040009

STEP 3: Convert Result to Output's Unit

0.0344000055040009 Meter -->34.4000055040009 Millimeter (Check conversion here)

FINAL ANSWER

34.4000055040009 ≈ 34.40001 Millimeter <-- Rivet Diameter

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Failure of A Riveted Joint » Mechanical » Failure Due to Crushing of Rivet or Plate » Diameter of rivet given strength of joint per pitch length (single rivet)

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Failure Due to Crushing of Rivet or Plate Calculators

Safe load which rivet can withstand against crushing

LaTeX Go Safe Load Joint = Crushing Stress*Rivet Diameter*Thickness of Plate

Allowable crushing stress given safe load which rivet can withstand for given projected area

LaTeX Go Crushing Stress = Safe Load Joint/(Projected Area)

Projected area given safe load which rivet can withstand against crushing

LaTeX Go Projected Area = Safe Load Joint/(Crushing Stress)

Safe load which rivet can withstand against crushing given projected area

LaTeX Go Safe Load Joint = Crushing Stress*Projected Area

Diameter of rivet given strength of joint per pitch length (single rivet) Formula

LaTeX Go

Rivet Diameter = Strength of Joint/(1*Crushing Stress*Thickness of Plate)
D_rivet = S/(1*σ_c*t_plate)

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Diameter of rivet given strength of joint per pitch length (single rivet)?

Diameter of rivet given strength of joint per pitch length (single rivet) calculator uses Rivet Diameter = Strength of Joint/(1*Crushing Stress*Thickness of Plate) to calculate the Rivet Diameter, The Diameter of rivet given strength of joint per pitch length (single rivet) formula is defined as a chord that runs through the centre point of the rivet. Rivet Diameter is denoted by D_rivet symbol.

How to calculate Diameter of rivet given strength of joint per pitch length (single rivet) using this online calculator? To use this online calculator for Diameter of rivet given strength of joint per pitch length (single rivet), enter Strength of Joint (S), Crushing Stress (σ_c) & Thickness of Plate (t_plate) and hit the calculate button. Here is how the Diameter of rivet given strength of joint per pitch length (single rivet) calculation can be explained with given input values -> 298611.1 = 8600/(1*20833330*0.012).

FAQ

What is Diameter of rivet given strength of joint per pitch length (single rivet)?

The Diameter of rivet given strength of joint per pitch length (single rivet) formula is defined as a chord that runs through the centre point of the rivet and is represented as D_rivet = S/(1*σ_c*t_plate) or Rivet Diameter = Strength of Joint/(1*Crushing Stress*Thickness of Plate). Strength of joint is the strength of riveted joint per pitch length, Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest & The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

How to calculate Diameter of rivet given strength of joint per pitch length (single rivet)?

The Diameter of rivet given strength of joint per pitch length (single rivet) formula is defined as a chord that runs through the centre point of the rivet is calculated using Rivet Diameter = Strength of Joint/(1*Crushing Stress*Thickness of Plate). To calculate Diameter of rivet given strength of joint per pitch length (single rivet), you need Strength of Joint (S), Crushing Stress (σ_c) & Thickness of Plate (t_plate). With our tool, you need to enter the respective value for Strength of Joint, Crushing Stress & Thickness of Plate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Rivet Diameter?

In this formula, Rivet Diameter uses Strength of Joint, Crushing Stress & Thickness of Plate. We can use 3 other way(s) to calculate the same, which is/are as follows -

Rivet Diameter = Safe Load Joint/(Crushing Stress*Thickness of Plate)
Rivet Diameter = Strength of Joint/(2*Crushing Stress*Thickness of Plate)
Rivet Diameter = Strength of Joint/(3*Crushing Stress*Thickness of Plate)

Home

FREE PDFs

🔍 Search