Diameter of rivet given shearing strength if rivet is in single shear Calculator

✖Shear Strength is the strength of a material or component against the type of yield or structural failure when the material or component fails in shear.ⓘ Shear Strength [V_n]			+10% -10%
✖Number of Rivets Per Pitch is defined as total number of rivets that are present on the pitch of the rivet.ⓘ Number of Rivets Per Pitch [n]			+10% -10%
✖Shear Stress in Joint is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.ⓘ Shear Stress in Joint [𝜏]			+10% -10%

✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Diameter of rivet given shearing strength if rivet is in single shear [D_rivet]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Diameter of rivet given shearing strength if rivet is in single shear Solution

STEP 0: Pre-Calculation Summary

Formula Used

Rivet Diameter = sqrt(Shear Strength/(1*Number of Rivets Per Pitch*(pi/4)*Shear Stress in Joint))
D_rivet = sqrt(V_n/(1*n*(pi/4)*𝜏))
This formula uses 1 Constants, 1 Functions, 4 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Functions Used

sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
Shear Strength - (Measured in Pascal) - Shear Strength is the strength of a material or component against the type of yield or structural failure when the material or component fails in shear.
Number of Rivets Per Pitch - Number of Rivets Per Pitch is defined as total number of rivets that are present on the pitch of the rivet.
Shear Stress in Joint - (Measured in Pascal) - Shear Stress in Joint is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.

STEP 1: Convert Input(s) to Base Unit

Shear Strength: 0.25 Megapascal --> 250000 Pascal (Check conversion here)
Number of Rivets Per Pitch: 2 --> No Conversion Required
Shear Stress in Joint: 4.6 Megapascal --> 4600000 Pascal (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

D_rivet = sqrt(V_n/(1*n*(pi/4)*𝜏)) --> sqrt(250000/(1*2*(pi/4)*4600000))

Evaluating ... ...

D_rivet = 0.186007797342346

STEP 3: Convert Result to Output's Unit

0.186007797342346 Meter -->186.007797342346 Millimeter (Check conversion here)

FINAL ANSWER

186.007797342346 ≈ 186.0078 Millimeter <-- Rivet Diameter

(Calculation completed in 00.020 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Strength of a Riveted Joint » Mechanical » Diameter of Rivet » Diameter of rivet given shearing strength if rivet is in single shear

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Diameter of Rivet Calculators

Diameter of rivet given crushing strength for 'n' number of rivets

LaTeX Go Rivet Diameter = Crushing strength/(Number of Rivets Per Pitch*Crushing Stress*Thickness of Plate)

Diameter of rivet given crushing strength for double rivet

LaTeX Go Rivet Diameter = Crushing strength/(2*Crushing Stress*Thickness of Plate)

Diameter of rivet given crushing strength for single rivet

LaTeX Go Rivet Diameter = Crushing strength/(1*Crushing Stress*Thickness of Plate)

Diameter of rivet given crushing strength for triple-rivet

LaTeX Go Rivet Diameter = Crushing strength/(3*Crushing Stress*Thickness of Plate)

Diameter of rivet given shearing strength if rivet is in single shear Formula

LaTeX Go

Rivet Diameter = sqrt(Shear Strength/(1*Number of Rivets Per Pitch*(pi/4)*Shear Stress in Joint))
D_rivet = sqrt(V_n/(1*n*(pi/4)*𝜏))

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Diameter of rivet given shearing strength if rivet is in single shear?

Diameter of rivet given shearing strength if rivet is in single shear calculator uses Rivet Diameter = sqrt(Shear Strength/(1*Number of Rivets Per Pitch*(pi/4)*Shear Stress in Joint)) to calculate the Rivet Diameter, The Diameter of rivet given shearing strength if rivet is in single shear formula is defined as a chord that runs through the center point of the rivet. Rivet Diameter is denoted by D_rivet symbol.

How to calculate Diameter of rivet given shearing strength if rivet is in single shear using this online calculator? To use this online calculator for Diameter of rivet given shearing strength if rivet is in single shear, enter Shear Strength (V_n), Number of Rivets Per Pitch (n) & Shear Stress in Joint (𝜏) and hit the calculate button. Here is how the Diameter of rivet given shearing strength if rivet is in single shear calculation can be explained with given input values -> 186007.8 = sqrt(250000/(1*2*(pi/4)*4600000)).

FAQ

What is Diameter of rivet given shearing strength if rivet is in single shear?

The Diameter of rivet given shearing strength if rivet is in single shear formula is defined as a chord that runs through the center point of the rivet and is represented as D_rivet = sqrt(V_n/(1*n*(pi/4)*𝜏)) or Rivet Diameter = sqrt(Shear Strength/(1*Number of Rivets Per Pitch*(pi/4)*Shear Stress in Joint)). Shear Strength is the strength of a material or component against the type of yield or structural failure when the material or component fails in shear, Number of Rivets Per Pitch is defined as total number of rivets that are present on the pitch of the rivet & Shear Stress in Joint is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.

How to calculate Diameter of rivet given shearing strength if rivet is in single shear?

The Diameter of rivet given shearing strength if rivet is in single shear formula is defined as a chord that runs through the center point of the rivet is calculated using Rivet Diameter = sqrt(Shear Strength/(1*Number of Rivets Per Pitch*(pi/4)*Shear Stress in Joint)). To calculate Diameter of rivet given shearing strength if rivet is in single shear, you need Shear Strength (V_n), Number of Rivets Per Pitch (n) & Shear Stress in Joint (𝜏). With our tool, you need to enter the respective value for Shear Strength, Number of Rivets Per Pitch & Shear Stress in Joint and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Rivet Diameter?

In this formula, Rivet Diameter uses Shear Strength, Number of Rivets Per Pitch & Shear Stress in Joint. We can use 3 other way(s) to calculate the same, which is/are as follows -

Rivet Diameter = Crushing strength/(2*Crushing Stress*Thickness of Plate)
Rivet Diameter = Crushing strength/(Number of Rivets Per Pitch*Crushing Stress*Thickness of Plate)
Rivet Diameter = Crushing strength/(1*Crushing Stress*Thickness of Plate)

Home

FREE PDFs

🔍 Search