Diameter of rivet(for dimension in cm) Solution

STEP 0: Pre-Calculation Summary
Formula Used
Rivet Diameter = 1.6*sqrt(Thickness of Plate)
Drivet = 1.6*sqrt(tplate)
This formula uses 1 Functions, 2 Variables
Functions Used
sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)
Variables Used
Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
STEP 1: Convert Input(s) to Base Unit
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion ​here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Drivet = 1.6*sqrt(tplate) --> 1.6*sqrt(0.012)
Evaluating ... ...
Drivet = 0.175271218401653
STEP 3: Convert Result to Output's Unit
0.175271218401653 Meter -->175.271218401653 Millimeter (Check conversion ​here)
FINAL ANSWER
175.271218401653 175.2712 Millimeter <-- Rivet Diameter
(Calculation completed in 00.004 seconds)

Credits

Creator Image
Created by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has created this Calculator and 2000+ more calculators!
Verifier Image
Verified by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has verified this Calculator and 1900+ more calculators!

Design of Riveted Joint Calculators

Diameter of rivet(for dimension in cm)
​ LaTeX ​ Go Rivet Diameter = 1.6*sqrt(Thickness of Plate)
Diameter of rivet
​ LaTeX ​ Go Rivet Diameter = 6*sqrt(Thickness of Plate)
Thickness of main plate(for dimension in cm)
​ LaTeX ​ Go Thickness of Plate = (Rivet Diameter/1.6)^2
Thickness of main plate(for dimension in mm)
​ LaTeX ​ Go Thickness of Plate = (Rivet Diameter/6)^2

Diameter of rivet(for dimension in cm) Formula

​LaTeX ​Go
Rivet Diameter = 1.6*sqrt(Thickness of Plate)
Drivet = 1.6*sqrt(tplate)

What is the difference between solid shank rivet and special rivet?

Two of the major types of rivets used in the aircraft are the common solid shank type, which must be driven using a bucking bar, and the special (blind) rivets, which may be installed where it is impossible to use a bucking bar. Solid shank rivets are generally used in repair work.

How to Calculate Diameter of rivet(for dimension in cm)?

Diameter of rivet(for dimension in cm) calculator uses Rivet Diameter = 1.6*sqrt(Thickness of Plate) to calculate the Rivet Diameter, The Diameter of rivet(for dimension in cm) formula is defined as a chord that runs through the center point of the rivet. Rivet Diameter is denoted by Drivet symbol.

How to calculate Diameter of rivet(for dimension in cm) using this online calculator? To use this online calculator for Diameter of rivet(for dimension in cm), enter Thickness of Plate (tplate) and hit the calculate button. Here is how the Diameter of rivet(for dimension in cm) calculation can be explained with given input values -> 175271.2 = 1.6*sqrt(0.012).

FAQ

What is Diameter of rivet(for dimension in cm)?
The Diameter of rivet(for dimension in cm) formula is defined as a chord that runs through the center point of the rivet and is represented as Drivet = 1.6*sqrt(tplate) or Rivet Diameter = 1.6*sqrt(Thickness of Plate). The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
How to calculate Diameter of rivet(for dimension in cm)?
The Diameter of rivet(for dimension in cm) formula is defined as a chord that runs through the center point of the rivet is calculated using Rivet Diameter = 1.6*sqrt(Thickness of Plate). To calculate Diameter of rivet(for dimension in cm), you need Thickness of Plate (tplate). With our tool, you need to enter the respective value for Thickness of Plate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Rivet Diameter?
In this formula, Rivet Diameter uses Thickness of Plate. We can use 2 other way(s) to calculate the same, which is/are as follows -
  • Rivet Diameter = 6*sqrt(Thickness of Plate)
  • Rivet Diameter = Pitch of Rivet*(1-Efficiency of riveted joint)
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!