Diameter of fulcrum pin of lever given reaction force and bearing pressure Calculator

✖The Force at Lever Fulcrum Pin is the force exerted at the pivot point of a lever, crucial for understanding the lever's mechanical advantage and performance.ⓘ Force at Lever Fulcrum Pin [R_f]			+10% -10%
✖The Bearing Pressure in Fulcrum Pin of Lever is the force exerted per unit area on the fulcrum pin, crucial for ensuring the lever's stability and performance.ⓘ Bearing Pressure in Fulcrum Pin of Lever [P_b]			+10% -10%
✖The Length of Lever Fulcrum Pin is the distance from the fulcrum to the point where the lever applies force, influencing the lever's mechanical advantage and efficiency.ⓘ Length of Lever Fulcrum Pin [l_f]			+10% -10%

✖The Diameter of Lever Fulcrum Pin is the measurement across the pin that serves as the pivot point in a lever system, affecting its mechanical advantage and stability.ⓘ Diameter of fulcrum pin of lever given reaction force and bearing pressure [d₁]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Design of Lever Formulas PDF PDF Image

Diameter of fulcrum pin of lever given reaction force and bearing pressure Solution

STEP 0: Pre-Calculation Summary

Formula Used

Diameter of Lever Fulcrum Pin = Force at Lever Fulcrum Pin/(Bearing Pressure in Fulcrum Pin of Lever*Length of Lever Fulcrum Pin)
d₁ = R_f/(P_b*l_f)
This formula uses 4 Variables

Variables Used

Diameter of Lever Fulcrum Pin - (Measured in Meter) - The Diameter of Lever Fulcrum Pin is the measurement across the pin that serves as the pivot point in a lever system, affecting its mechanical advantage and stability.
Force at Lever Fulcrum Pin - (Measured in Newton) - The Force at Lever Fulcrum Pin is the force exerted at the pivot point of a lever, crucial for understanding the lever's mechanical advantage and performance.
Bearing Pressure in Fulcrum Pin of Lever - (Measured in Pascal) - The Bearing Pressure in Fulcrum Pin of Lever is the force exerted per unit area on the fulcrum pin, crucial for ensuring the lever's stability and performance.
Length of Lever Fulcrum Pin - (Measured in Meter) - The Length of Lever Fulcrum Pin is the distance from the fulcrum to the point where the lever applies force, influencing the lever's mechanical advantage and efficiency.

STEP 1: Convert Input(s) to Base Unit

Force at Lever Fulcrum Pin: 2964 Newton --> 2964 Newton No Conversion Required
Bearing Pressure in Fulcrum Pin of Lever: 20.8 Newton per Square Millimeter --> 20800000 Pascal (Check conversion here)
Length of Lever Fulcrum Pin: 11.5 Millimeter --> 0.0115 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

d₁ = R_f/(P_b*l_f) --> 2964/(20800000*0.0115)

Evaluating ... ...

d₁ = 0.0123913043478261

STEP 3: Convert Result to Output's Unit

0.0123913043478261 Meter -->12.3913043478261 Millimeter (Check conversion here)

FINAL ANSWER

12.3913043478261 ≈ 12.3913 Millimeter <-- Diameter of Lever Fulcrum Pin

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Mechanical » Machine Design » Design of Lever » Design of Fulcrum Pin » Diameter of fulcrum pin of lever given reaction force and bearing pressure

Credits

Created by Saurabh Patil

Shri Govindram Seksaria Institute of Technology and Science (SGSITS ), Indore

Saurabh Patil has created this Calculator and 700+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Design of Fulcrum Pin Calculators

Bearing pressure in fulcrum pin of lever given reaction force and diameter of pin

LaTeX Go Bearing Pressure in Fulcrum Pin of Lever = Force at Lever Fulcrum Pin/(Diameter of Lever Fulcrum Pin*Length of Lever Fulcrum Pin)

Diameter of fulcrum pin of lever given reaction force and bearing pressure

LaTeX Go Diameter of Lever Fulcrum Pin = Force at Lever Fulcrum Pin/(Bearing Pressure in Fulcrum Pin of Lever*Length of Lever Fulcrum Pin)

Length of flucrum pin of lever given reaction force and bearing pressure

LaTeX Go Length of Lever Fulcrum Pin = Force at Lever Fulcrum Pin/(Bearing Pressure in Fulcrum Pin of Lever*Diameter of Lever Fulcrum Pin)

Diameter of fulcrum pin of lever given bending moment and effort force

LaTeX Go Diameter of Lever Fulcrum Pin = (Length of Effort Arm)-(Bending Moment in Lever/Effort on Lever)

Diameter of fulcrum pin of lever given reaction force and bearing pressure Formula

LaTeX Go

Diameter of Lever Fulcrum Pin = Force at Lever Fulcrum Pin/(Bearing Pressure in Fulcrum Pin of Lever*Length of Lever Fulcrum Pin)
d₁ = R_f/(P_b*l_f)

Principal Of Lever

A lever works by reducing the amount of force needed to move an object or lift a load. A lever does this by increasing the distance through which the force acts. Instead, they make the work easier by spreading out the effort over a longer distance.
It has been practically found that when two equal forces acting in opposite directions, i.e., clockwise and counterclockwise, are applied to a uniform lever at equal distances from the fulcrum, they counteract each other and establish a state of equilibrium in the lever.

How to Calculate Diameter of fulcrum pin of lever given reaction force and bearing pressure?

Diameter of fulcrum pin of lever given reaction force and bearing pressure calculator uses Diameter of Lever Fulcrum Pin = Force at Lever Fulcrum Pin/(Bearing Pressure in Fulcrum Pin of Lever*Length of Lever Fulcrum Pin) to calculate the Diameter of Lever Fulcrum Pin, Diameter of fulcrum pin of lever given reaction force and bearing pressure formula is defined as a method to determine the diameter of the fulcrum pin based on the reaction force and bearing pressure in a lever system. Diameter of Lever Fulcrum Pin is denoted by d₁ symbol.

How to calculate Diameter of fulcrum pin of lever given reaction force and bearing pressure using this online calculator? To use this online calculator for Diameter of fulcrum pin of lever given reaction force and bearing pressure, enter Force at Lever Fulcrum Pin (R_f), Bearing Pressure in Fulcrum Pin of Lever (P_b) & Length of Lever Fulcrum Pin (l_f) and hit the calculate button. Here is how the Diameter of fulcrum pin of lever given reaction force and bearing pressure calculation can be explained with given input values -> 12391.3 = 2964/(20800000*0.0115).

FAQ

What is Diameter of fulcrum pin of lever given reaction force and bearing pressure?

Diameter of fulcrum pin of lever given reaction force and bearing pressure formula is defined as a method to determine the diameter of the fulcrum pin based on the reaction force and bearing pressure in a lever system and is represented as d₁ = R_f/(P_b*l_f) or Diameter of Lever Fulcrum Pin = Force at Lever Fulcrum Pin/(Bearing Pressure in Fulcrum Pin of Lever*Length of Lever Fulcrum Pin). The Force at Lever Fulcrum Pin is the force exerted at the pivot point of a lever, crucial for understanding the lever's mechanical advantage and performance, The Bearing Pressure in Fulcrum Pin of Lever is the force exerted per unit area on the fulcrum pin, crucial for ensuring the lever's stability and performance & The Length of Lever Fulcrum Pin is the distance from the fulcrum to the point where the lever applies force, influencing the lever's mechanical advantage and efficiency.

How to calculate Diameter of fulcrum pin of lever given reaction force and bearing pressure?

Diameter of fulcrum pin of lever given reaction force and bearing pressure formula is defined as a method to determine the diameter of the fulcrum pin based on the reaction force and bearing pressure in a lever system is calculated using Diameter of Lever Fulcrum Pin = Force at Lever Fulcrum Pin/(Bearing Pressure in Fulcrum Pin of Lever*Length of Lever Fulcrum Pin). To calculate Diameter of fulcrum pin of lever given reaction force and bearing pressure, you need Force at Lever Fulcrum Pin (R_f), Bearing Pressure in Fulcrum Pin of Lever (P_b) & Length of Lever Fulcrum Pin (l_f). With our tool, you need to enter the respective value for Force at Lever Fulcrum Pin, Bearing Pressure in Fulcrum Pin of Lever & Length of Lever Fulcrum Pin and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Diameter of Lever Fulcrum Pin?

In this formula, Diameter of Lever Fulcrum Pin uses Force at Lever Fulcrum Pin, Bearing Pressure in Fulcrum Pin of Lever & Length of Lever Fulcrum Pin. We can use 2 other way(s) to calculate the same, which is/are as follows -

Diameter of Lever Fulcrum Pin = (Length of Effort Arm)-(Bending Moment in Lever/Effort on Lever)
Diameter of Lever Fulcrum Pin = Force at Lever Fulcrum Pin/(Compressive Stress in Fulcrum Pin*Length of Pin Boss)

Home

FREE PDFs

🔍 Search