Design of Shell Thickness Subjected to Internal Pressure Calculator

✖Internal Pressure in Vessel is a measure of how the internal energy of a system changes when it expands or contracts at constant temperature.ⓘ Internal Pressure in Vessel [p]			+10% -10%
✖Internal Diameter of Shell is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside.ⓘ Internal Diameter of Shell [D_i]			+10% -10%
✖Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.ⓘ Allowable Stress for Jacket Material [f_j]			+10% -10%
✖Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank.ⓘ Joint Efficiency for Shell [J]			+10% -10%
✖Corrosion allowance is defined as an extra thickness normally added to carbon and low alloy steel to mitigate the CO2 corrosion rate.ⓘ Corrosion Allowance [c]			+10% -10%

✖Shell Thickness for Jackted Reaction Vessel is the distance through the shell.ⓘ Design of Shell Thickness Subjected to Internal Pressure [t_{jacketedreaction}]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Jacketed Reaction Vessel Formulas PDF PDF Image

Design of Shell Thickness Subjected to Internal Pressure Solution

STEP 0: Pre-Calculation Summary

Formula Used

Shell Thickness for Jackted Reaction Vessel = (Internal Pressure in Vessel*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-(Internal Pressure in Vessel))+Corrosion Allowance
t_{jacketedreaction} = (p*D_i)/((2*f_j*J)-(p))+c
This formula uses 6 Variables

Variables Used

Shell Thickness for Jackted Reaction Vessel - (Measured in Millimeter) - Shell Thickness for Jackted Reaction Vessel is the distance through the shell.
Internal Pressure in Vessel - (Measured in Newton per Square Millimeter) - Internal Pressure in Vessel is a measure of how the internal energy of a system changes when it expands or contracts at constant temperature.
Internal Diameter of Shell - (Measured in Millimeter) - Internal Diameter of Shell is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside.
Allowable Stress for Jacket Material - (Measured in Newton per Square Millimeter) - Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one.
Joint Efficiency for Shell - Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank.
Corrosion Allowance - (Measured in Millimeter) - Corrosion allowance is defined as an extra thickness normally added to carbon and low alloy steel to mitigate the CO2 corrosion rate.

STEP 1: Convert Input(s) to Base Unit

Internal Pressure in Vessel: 0.52 Newton per Square Millimeter --> 0.52 Newton per Square Millimeter No Conversion Required
Internal Diameter of Shell: 1500 Millimeter --> 1500 Millimeter No Conversion Required
Allowable Stress for Jacket Material: 120 Newton per Square Millimeter --> 120 Newton per Square Millimeter No Conversion Required
Joint Efficiency for Shell: 0.85 --> No Conversion Required
Corrosion Allowance: 10.5 Millimeter --> 10.5 Millimeter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t_{jacketedreaction} = (p*D_i)/((2*f_j*J)-(p))+c --> (0.52*1500)/((2*120*0.85)-(0.52))+10.5

Evaluating ... ...

t_{jacketedreaction} = 14.3333005700806

STEP 3: Convert Result to Output's Unit

0.0143333005700806 Meter -->14.3333005700806 Millimeter (Check conversion here)

FINAL ANSWER

14.3333005700806 ≈ 14.3333 Millimeter <-- Shell Thickness for Jackted Reaction Vessel

(Calculation completed in 00.011 seconds)

You are here -

Home » Engineering » Chemical Engineering » Process Equipment Design » Jacketed Reaction Vessel » Design of Shell Thickness Subjected to Internal Pressure

Credits

Created by Heet

Thadomal Shahani Engineering College (Tsec), Mumbai

Heet has created this Calculator and 200+ more calculators!

Verified by Prerana Bakli

University of Hawaiʻi at Mānoa (UH Manoa), Hawaii, USA

Prerana Bakli has verified this Calculator and 1600+ more calculators!

< Jacketed Reaction Vessel Calculators

Maximum Hoop Stress in Coil at Junction with Shell

LaTeX Go Maximum Hoop Stress in Coil at Junction with Shell = (Design Jacket Pressure*Internal Diameter of Half Coil)/(2*Thickness of Half Coil Jacket*Weld Joint Efficiency Factor for Coil)

Required Plate Thickness for Dimple Jacket

LaTeX Go Required Thickness of Dimple Jacket = Maximum Pitch between Steam Weld Centre Lines*sqrt(Design Jacket Pressure/(3*Allowable Stress for Jacket Material))

Required Thickness for Jacket Closer Member with Jacket Width

LaTeX Go Required Thickness for Jacket Closer Member = 0.886*Jacket Width*sqrt(Design Jacket Pressure/Allowable Stress for Jacket Material)

Jacket Width

LaTeX Go Jacket Width = (Inside Diameter of Jacket-Outer Diameter of Vessel)/2

Design of Shell Thickness Subjected to Internal Pressure Formula

LaTeX Go

What is Design Thickness?

Design thickness is a term used in structural engineering to refer to the thickness of a structural element (such as a beam, column, or plate) that has been calculated or specified based on the design requirements of the structure. The design thickness is the thickness that has been calculated or specified based on the structural requirements of the beam and the strength and deformability of the soil or foundation on which the beam will be supported. The design thickness of a bottom plate is typically determined by a structural engineer or using structural engineering software, and is used to ensure that the bottom plate is able to safely carry the loads that will be applied to it during the life of the structure.

How to Calculate Design of Shell Thickness Subjected to Internal Pressure?

Design of Shell Thickness Subjected to Internal Pressure calculator uses Shell Thickness for Jackted Reaction Vessel = (Internal Pressure in Vessel*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-(Internal Pressure in Vessel))+Corrosion Allowance to calculate the Shell Thickness for Jackted Reaction Vessel, The Design of Shell Thickness Subjected to Internal Pressure formula is defined as is the distance from the external part to the internal part of a Shell. Shell Thickness for Jackted Reaction Vessel is denoted by t_{jacketedreaction} symbol.

How to calculate Design of Shell Thickness Subjected to Internal Pressure using this online calculator? To use this online calculator for Design of Shell Thickness Subjected to Internal Pressure, enter Internal Pressure in Vessel (p), Internal Diameter of Shell (D_i), Allowable Stress for Jacket Material (f_j), Joint Efficiency for Shell (J) & Corrosion Allowance (c) and hit the calculate button. Here is how the Design of Shell Thickness Subjected to Internal Pressure calculation can be explained with given input values -> 14333.3 = (520000*1.5)/((2*120000000*0.85)-(520000))+0.0105.

FAQ

What is Design of Shell Thickness Subjected to Internal Pressure?

The Design of Shell Thickness Subjected to Internal Pressure formula is defined as is the distance from the external part to the internal part of a Shell and is represented as t_{jacketedreaction} = (p*D_i)/((2*f_j*J)-(p))+c or Shell Thickness for Jackted Reaction Vessel = (Internal Pressure in Vessel*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-(Internal Pressure in Vessel))+Corrosion Allowance. Internal Pressure in Vessel is a measure of how the internal energy of a system changes when it expands or contracts at constant temperature, Internal Diameter of Shell is a measurement of the distance of a straight line from one point on the inner wall of the object, through its center, to an opposite point also on the inside, Allowable Stress for Jacket Material at Design Temperature is defined as the material failure stress divided by a factor of safety greater than one, Joint Efficiency for Shell refers to the effectiveness of the joint between two adjacent sections of a cylindrical shell, such as in a pressure vessel or a storage tank & Corrosion allowance is defined as an extra thickness normally added to carbon and low alloy steel to mitigate the CO2 corrosion rate.

How to calculate Design of Shell Thickness Subjected to Internal Pressure?

The Design of Shell Thickness Subjected to Internal Pressure formula is defined as is the distance from the external part to the internal part of a Shell is calculated using Shell Thickness for Jackted Reaction Vessel = (Internal Pressure in Vessel*Internal Diameter of Shell)/((2*Allowable Stress for Jacket Material*Joint Efficiency for Shell)-(Internal Pressure in Vessel))+Corrosion Allowance. To calculate Design of Shell Thickness Subjected to Internal Pressure, you need Internal Pressure in Vessel (p), Internal Diameter of Shell (D_i), Allowable Stress for Jacket Material (f_j), Joint Efficiency for Shell (J) & Corrosion Allowance (c). With our tool, you need to enter the respective value for Internal Pressure in Vessel, Internal Diameter of Shell, Allowable Stress for Jacket Material, Joint Efficiency for Shell & Corrosion Allowance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search