Deflection of Spring Initial Bolt Load to Seal Gasket Joint Calculator

✖Initial bolt load to seat the gasket joint contact surface is defined as load in terms of either a concentrated force or a prescribed change in length.ⓘ Initial Bolt Load to Seat the Gasket Joint [W_m2]			+10% -10%
✖Width of u-collar in Gasket is definied as the measurement or extent of u-collar from side to side.ⓘ Width of u-collar in Gasket [b_g]			+10% -10%
✖Gasket Diameter is a straight line passing from side to side through the centre of a gasket.ⓘ Gasket Diameter [G]			+10% -10%

✖Gasket Unit Seating Load is the seating load on per unit area o the sealing gasket.ⓘ Deflection of Spring Initial Bolt Load to Seal Gasket Joint [y_sl]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Bolt Loads in Gasket Joints Formulas PDF PDF Image

Deflection of Spring Initial Bolt Load to Seal Gasket Joint Solution

STEP 0: Pre-Calculation Summary

Formula Used

Gasket Unit Seating Load = Initial Bolt Load to Seat the Gasket Joint/(pi*Width of u-collar in Gasket*Gasket Diameter)
y_sl = W_m2/(pi*b_g*G)
This formula uses 1 Constants, 4 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Gasket Unit Seating Load - (Measured in Pascal) - Gasket Unit Seating Load is the seating load on per unit area o the sealing gasket.
Initial Bolt Load to Seat the Gasket Joint - (Measured in Newton) - Initial bolt load to seat the gasket joint contact surface is defined as load in terms of either a concentrated force or a prescribed change in length.
Width of u-collar in Gasket - (Measured in Meter) - Width of u-collar in Gasket is definied as the measurement or extent of u-collar from side to side.
Gasket Diameter - (Measured in Meter) - Gasket Diameter is a straight line passing from side to side through the centre of a gasket.

STEP 1: Convert Input(s) to Base Unit

Initial Bolt Load to Seat the Gasket Joint: 1605 Newton --> 1605 Newton No Conversion Required
Width of u-collar in Gasket: 4.21 Millimeter --> 0.00421 Meter (Check conversion here)
Gasket Diameter: 32 Millimeter --> 0.032 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

y_sl = W_m2/(pi*b_g*G) --> 1605/(pi*0.00421*0.032)

Evaluating ... ...

y_sl = 3792216.20639091

STEP 3: Convert Result to Output's Unit

3792216.20639091 Pascal -->3.79221620639091 Newton per Square Millimeter (Check conversion here)

FINAL ANSWER

3.79221620639091 ≈ 3.792216 Newton per Square Millimeter <-- Gasket Unit Seating Load

(Calculation completed in 00.020 seconds)

You are here -

Home » Physics » Design of Machine Elements » Design of Coupling » Packing » Mechanical » Bolt Loads in Gasket Joints » Deflection of Spring Initial Bolt Load to Seal Gasket Joint

Credits

Created by sanjay shiva

national institute of technology hamirpur (NITH ), hamirpur , himachal pradesh

sanjay shiva has created this Calculator and 100+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Bolt Loads in Gasket Joints Calculators

Bolt Load under operating condition given Hydrostatic End Force

LaTeX Go Bolt Load Under Operating Condition for Gasket = ((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)+(2*Width of u-collar in Gasket*pi*Gasket Diameter*Pressure at Outer Diameter of Gasket*Gasket Factor)

Hydrostatic End Force given Bolt Load under Operating condition

LaTeX Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-(2*Width of u-collar in Gasket*pi*Gasket Diameter*Gasket Factor*Pressure at Outer Diameter of Gasket)

Bolt load under operating condition

LaTeX Go Bolt Load Under Operating Condition for Gasket = Hydrostatic End Force in Gasket Seal+Total Joint Surface Compression Load

Hydrostatic end force

LaTeX Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-Total Joint Surface Compression Load

Deflection of Spring Initial Bolt Load to Seal Gasket Joint Formula

LaTeX Go

Gasket Unit Seating Load = Initial Bolt Load to Seat the Gasket Joint/(pi*Width of u-collar in Gasket*Gasket Diameter)
y_sl = W_m2/(pi*b_g*G)

What is Deflection of Spring?

Deflection of Spring is how a spring responds when force is applied or released. That is, whatever load you are applying to the spring divided by the spring’s rate of deflection will produce the amount of deflection that will occur.

How to Calculate Deflection of Spring Initial Bolt Load to Seal Gasket Joint?

Deflection of Spring Initial Bolt Load to Seal Gasket Joint calculator uses Gasket Unit Seating Load = Initial Bolt Load to Seat the Gasket Joint/(pi*Width of u-collar in Gasket*Gasket Diameter) to calculate the Gasket Unit Seating Load, The Deflection of Spring Initial Bolt Load to Seal Gasket Joint formula is defined as how a spring responds when force is applied or released. Gasket Unit Seating Load is denoted by y_sl symbol.

How to calculate Deflection of Spring Initial Bolt Load to Seal Gasket Joint using this online calculator? To use this online calculator for Deflection of Spring Initial Bolt Load to Seal Gasket Joint, enter Initial Bolt Load to Seat the Gasket Joint (W_m2), Width of u-collar in Gasket (b_g) & Gasket Diameter (G) and hit the calculate button. Here is how the Deflection of Spring Initial Bolt Load to Seal Gasket Joint calculation can be explained with given input values -> 3.8E-6 = 1605/(pi*0.00421*0.032).

FAQ

What is Deflection of Spring Initial Bolt Load to Seal Gasket Joint?

The Deflection of Spring Initial Bolt Load to Seal Gasket Joint formula is defined as how a spring responds when force is applied or released and is represented as y_sl = W_m2/(pi*b_g*G) or Gasket Unit Seating Load = Initial Bolt Load to Seat the Gasket Joint/(pi*Width of u-collar in Gasket*Gasket Diameter). Initial bolt load to seat the gasket joint contact surface is defined as load in terms of either a concentrated force or a prescribed change in length, Width of u-collar in Gasket is definied as the measurement or extent of u-collar from side to side & Gasket Diameter is a straight line passing from side to side through the centre of a gasket.

How to calculate Deflection of Spring Initial Bolt Load to Seal Gasket Joint?

The Deflection of Spring Initial Bolt Load to Seal Gasket Joint formula is defined as how a spring responds when force is applied or released is calculated using Gasket Unit Seating Load = Initial Bolt Load to Seat the Gasket Joint/(pi*Width of u-collar in Gasket*Gasket Diameter). To calculate Deflection of Spring Initial Bolt Load to Seal Gasket Joint, you need Initial Bolt Load to Seat the Gasket Joint (W_m2), Width of u-collar in Gasket (b_g) & Gasket Diameter (G). With our tool, you need to enter the respective value for Initial Bolt Load to Seat the Gasket Joint, Width of u-collar in Gasket & Gasket Diameter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search