Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS Calculator

✖The Process Transconductance Parameter in NMOS (PTM) is a parameter used in semiconductor device modeling to characterize the performance of a transistor.ⓘ Process Transconductance Parameter in NMOS [k'_n]			+10% -10%
✖The width of channel refers to the amount of bandwidth available for transmitting data within a communication channel.ⓘ Width of Channel [W_c]			+10% -10%
✖Length of the channel can be defined as the distance between its start and end points, and can vary greatly depending on its purpose and location.ⓘ Length of the Channel [L]			+10% -10%
✖Drain Source Voltage is an electrical term used in electronics and specifically in field-effect transistors . It refers to the voltage difference between the Drain and Source terminals of the FET.ⓘ Drain Source Voltage [V_ds]			+10% -10%

✖Drain current in NMOS is the electric current flowing from the drain to the source of a field-effect transistor (FET) or a metal-oxide-semiconductor field-effect transistor (MOSFET).ⓘ Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS [I_d]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download MOSFET Formula PDF PDF Image

Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS Solution

STEP 0: Pre-Calculation Summary

Formula Used

Drain Current in NMOS = 1/2*Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*(Drain Source Voltage)^2
I_d = 1/2*k'_n*W_c/L*(V_ds)^2
This formula uses 5 Variables

Variables Used

Drain Current in NMOS - (Measured in Ampere) - Drain current in NMOS is the electric current flowing from the drain to the source of a field-effect transistor (FET) or a metal-oxide-semiconductor field-effect transistor (MOSFET).
Process Transconductance Parameter in NMOS - (Measured in Siemens) - The Process Transconductance Parameter in NMOS (PTM) is a parameter used in semiconductor device modeling to characterize the performance of a transistor.
Width of Channel - (Measured in Meter) - The width of channel refers to the amount of bandwidth available for transmitting data within a communication channel.
Length of the Channel - (Measured in Meter) - Length of the channel can be defined as the distance between its start and end points, and can vary greatly depending on its purpose and location.
Drain Source Voltage - (Measured in Volt) - Drain Source Voltage is an electrical term used in electronics and specifically in field-effect transistors . It refers to the voltage difference between the Drain and Source terminals of the FET.

STEP 1: Convert Input(s) to Base Unit

Process Transconductance Parameter in NMOS: 2 Millisiemens --> 0.002 Siemens (Check conversion here)
Width of Channel: 10 Micrometer --> 1E-05 Meter (Check conversion here)
Length of the Channel: 3 Micrometer --> 3E-06 Meter (Check conversion here)
Drain Source Voltage: 8.43 Volt --> 8.43 Volt No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

I_d = 1/2*k'_n*W_c/L*(V_ds)^2 --> 1/2*0.002*1E-05/3E-06*(8.43)^2

Evaluating ... ...

I_d = 0.236883

STEP 3: Convert Result to Output's Unit

0.236883 Ampere -->236.883 Milliampere (Check conversion here)

FINAL ANSWER

236.883 Milliampere <-- Drain Current in NMOS

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics » MOSFET » Analog Electronics » N Channel Enhancement » Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS

Credits

Created by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has created this Calculator and 600+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< N Channel Enhancement Calculators

Current Entering Drain-Source in Triode Region of NMOS

LaTeX Go Drain Current in NMOS = Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*((Gate Source Voltage-Threshold Voltage)*Drain Source Voltage-1/2*(Drain Source Voltage)^2)

Current Entering Drain Terminal of NMOS given Gate Source Voltage

NMOS as Linear Resistance

LaTeX Go Linear Resistance = Length of the Channel/(Mobility of Electrons at Surface of Channel*Oxide Capacitance*Width of Channel*(Gate Source Voltage-Threshold Voltage))

Electron Drift Velocity of Channel in NMOS Transistor

LaTeX Go Electron Drift Velocity = Mobility of Electrons at Surface of Channel*Electric Field across Length of Channel

Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS Formula

LaTeX Go

Drain Current in NMOS = 1/2*Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*(Drain Source Voltage)^2
I_d = 1/2*k'_n*W_c/L*(V_ds)^2

What is NMOS?

NMOS (MOSFET) is a kind of MOSFET. An NMOS transistor consists of an n-type source and drain and a p-type substrate. When a voltage is applied to the gate, holes in the body (p-type substrate) are driven away from the gate. This allows the formation of an n-type channel between the source and the drain, and a current is conducted from electrons from the source to the drain through an induced n-type channel.

Logic gates and other digital devices implemented using NMOSs are said to have NMOS logic. There are three operating modes in an NMOS called cut-off, triode, and saturation. NMOS logic is easy to design and manufacture. Circuits with NMOS logic gates, however, consume static power when the circuit is idle since DC current flows through the logic gate when the output is low.

How to Calculate Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS?

Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS calculator uses Drain Current in NMOS = 1/2*Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*(Drain Source Voltage)^2 to calculate the Drain Current in NMOS, The Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS formula indicates the current conduction capability of the silicon chip; it can be used as a guide when comparing different devices. Drain Current in NMOS is denoted by I_d symbol.

How to calculate Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS using this online calculator? To use this online calculator for Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS, enter Process Transconductance Parameter in NMOS (k'_n), Width of Channel (W_c), Length of the Channel (L) & Drain Source Voltage (V_ds) and hit the calculate button. Here is how the Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS calculation can be explained with given input values -> 236883 = 1/2*0.002*1E-05/3E-06*(8.43)^2.

FAQ

What is Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS?

The Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS formula indicates the current conduction capability of the silicon chip; it can be used as a guide when comparing different devices and is represented as I_d = 1/2*k'_n*W_c/L*(V_ds)^2 or Drain Current in NMOS = 1/2*Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*(Drain Source Voltage)^2. The Process Transconductance Parameter in NMOS (PTM) is a parameter used in semiconductor device modeling to characterize the performance of a transistor, The width of channel refers to the amount of bandwidth available for transmitting data within a communication channel, Length of the channel can be defined as the distance between its start and end points, and can vary greatly depending on its purpose and location & Drain Source Voltage is an electrical term used in electronics and specifically in field-effect transistors . It refers to the voltage difference between the Drain and Source terminals of the FET.

How to calculate Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS?

The Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS formula indicates the current conduction capability of the silicon chip; it can be used as a guide when comparing different devices is calculated using Drain Current in NMOS = 1/2*Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*(Drain Source Voltage)^2. To calculate Current Entering Drain Source at Boundary of Saturation and Triode Region of NMOS, you need Process Transconductance Parameter in NMOS (k'_n), Width of Channel (W_c), Length of the Channel (L) & Drain Source Voltage (V_ds). With our tool, you need to enter the respective value for Process Transconductance Parameter in NMOS, Width of Channel, Length of the Channel & Drain Source Voltage and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Drain Current in NMOS?

In this formula, Drain Current in NMOS uses Process Transconductance Parameter in NMOS, Width of Channel, Length of the Channel & Drain Source Voltage. We can use 3 other way(s) to calculate the same, which is/are as follows -

Drain Current in NMOS = Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*((Gate Source Voltage-Threshold Voltage)*Drain Source Voltage-1/2*Drain Source Voltage^2)
Drain Current in NMOS = Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*((Gate Source Voltage-Threshold Voltage)*Drain Source Voltage-1/2*(Drain Source Voltage)^2)
Drain Current in NMOS = 1/2*Process Transconductance Parameter in NMOS*Width of Channel/Length of the Channel*(Gate Source Voltage-Threshold Voltage)^2

Home

FREE PDFs

🔍 Search