LCM calculator

Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 Calculator

Engineering Chemistry Financial Health More >>

↳

Civil Chemical Engineering Electrical Electronics More >>

⤿

Environmental Engineering Bridge and Suspension Cable Coastal and Ocean Engineering Columns More >>

⤿

Water Resources Ground Water Conveyance of Water Design of a Chlorination System for Wastewater Disinfection Design of a Circular Settling Tank More >>

⤿

Yield of an Open Well Basic Definitions Characteristic Well Losses Confined Aquifers More >>

⤿

Recuperation Test Constant Level Pumping Test

⤿

Cross Sectional Area of Well Constant Depending upon Base Soil Depression Head after Pumping Stopped Depression Head when Pumping Stopped More >>

✖Constant Dependent on Base Soil is the constant depending on the soil at the base of the well.ⓘ Constant Dependent on Base Soil [K_b]			+10% -10%
✖Time refers to the ongoing and continuous sequence of events that occur in succession, from the past through the present to the future.ⓘ Time [t]			+10% -10%
✖Depression Head in Well is the depression head in the well when pumping stopped.ⓘ Depression Head in Well [h1']			+10% -10%
✖Depression Head in Well 2 is depression head in the well at a time T after the pumping stopped.ⓘ Depression Head in Well 2 [h_w2]			+10% -10%

✖Cross-Sectional Area given Specific Capacity is the cross-sectional area of the wellbore through which water flows.ⓘ Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 [A_sec]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Recuperation Test Formulas PDF PDF Image

Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 Solution

STEP 0: Pre-Calculation Summary

Formula Used

Cross-Sectional Area given Specific Capacity = Constant Dependent on Base Soil/((2.303/Time)*log((Depression Head in Well/Depression Head in Well 2),10))
A_sec = K_b/((2.303/t)*log((h1'/h_w2),10))
This formula uses 1 Functions, 5 Variables

Functions Used

log - Logarithmic function is an inverse function to exponentiation., log(Base, Number)

Variables Used

Cross-Sectional Area given Specific Capacity - (Measured in Square Meter) - Cross-Sectional Area given Specific Capacity is the cross-sectional area of the wellbore through which water flows.
Constant Dependent on Base Soil - (Measured in Cubic Meter per Second) - Constant Dependent on Base Soil is the constant depending on the soil at the base of the well.
Time - (Measured in Second) - Time refers to the ongoing and continuous sequence of events that occur in succession, from the past through the present to the future.
Depression Head in Well - (Measured in Meter) - Depression Head in Well is the depression head in the well when pumping stopped.
Depression Head in Well 2 - (Measured in Meter) - Depression Head in Well 2 is depression head in the well at a time T after the pumping stopped.

STEP 1: Convert Input(s) to Base Unit

Constant Dependent on Base Soil: 4.99 Cubic Meter per Hour --> 0.00138611111111111 Cubic Meter per Second (Check conversion here)
Time: 4 Hour --> 14400 Second (Check conversion here)
Depression Head in Well: 20 Meter --> 20 Meter No Conversion Required
Depression Head in Well 2: 10 Meter --> 10 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

A_sec = K_b/((2.303/t)*log((h1'/h_w2),10)) --> 0.00138611111111111/((2.303/14400)*log((20/10),10))

Evaluating ... ...

A_sec = 2.60901377049634

STEP 3: Convert Result to Output's Unit

2.60901377049634 Square Meter --> No Conversion Required

FINAL ANSWER

2.60901377049634 ≈ 2.609014 Square Meter <-- Cross-Sectional Area given Specific Capacity

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Civil » Environmental Engineering » Water Resources Ground Water » Yield of an Open Well » Recuperation Test » Cross Sectional Area of Well » Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10

Credits

Created by Suraj Kumar

Birsa Institute of Technology (BIT), Sindri

Suraj Kumar has created this Calculator and 2100+ more calculators!

Verified by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has verified this Calculator and 2600+ more calculators!

< Cross Sectional Area of Well Calculators

Cross-sectional Area of Well given Constant Depending upon Soil at Base

LaTeX Go Cross-Sectional Area of Well = Constant Dependent on Base Soil/((1/Time)*log((Depression Head in Well/Depression Head in Well 2),e))

Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10

LaTeX Go Cross-Sectional Area given Specific Capacity = Constant Dependent on Base Soil/((2.303/Time)*log((Depression Head in Well/Depression Head in Well 2),10))

Cross-sectional Area of Well given Discharge from Well

LaTeX Go Cross-Sectional Area of Well = Discharge in Well/(Specific Capacity in SI unit*Constant Depression Head)

Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 Formula

LaTeX Go

Cross-Sectional Area given Specific Capacity = Constant Dependent on Base Soil/((2.303/Time)*log((Depression Head in Well/Depression Head in Well 2),10))
A_sec = K_b/((2.303/t)*log((h1'/h_w2),10))

What is Cross-Sectional Area?

Cross-sectional area refers to the area of an object or fluid flow, as viewed or cut through at a particular section perpendicular to its length or flow direction. In simpler terms, it's the surface area exposed when an object is sliced across a particular plane. In fluid dynamics and well systems, the cross-sectional area plays a key role in determining flow rates, as it is used in calculating discharge (flow rate). For example, when water flows through a pipe or well, the cross-sectional area of the pipe or well impacts how much water can flow through it at any given time.

How to Calculate Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10?

Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 calculator uses Cross-Sectional Area given Specific Capacity = Constant Dependent on Base Soil/((2.303/Time)*log((Depression Head in Well/Depression Head in Well 2),10)) to calculate the Cross-Sectional Area given Specific Capacity, The Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 formula is defined as the calculation of value of cross-sectional area of well when we have prior information of other parameters used. Cross-Sectional Area given Specific Capacity is denoted by A_sec symbol.

How to calculate Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 using this online calculator? To use this online calculator for Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10, enter Constant Dependent on Base Soil (K_b), Time (t), Depression Head in Well (h1') & Depression Head in Well 2 (h_w2) and hit the calculate button. Here is how the Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 calculation can be explained with given input values -> 2.609014 = 0.00138611111111111/((2.303/14400)*log((20/10),10)).

FAQ

What is Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10?

The Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 formula is defined as the calculation of value of cross-sectional area of well when we have prior information of other parameters used and is represented as A_sec = K_b/((2.303/t)*log((h1'/h_w2),10)) or Cross-Sectional Area given Specific Capacity = Constant Dependent on Base Soil/((2.303/Time)*log((Depression Head in Well/Depression Head in Well 2),10)). Constant Dependent on Base Soil is the constant depending on the soil at the base of the well, Time refers to the ongoing and continuous sequence of events that occur in succession, from the past through the present to the future, Depression Head in Well is the depression head in the well when pumping stopped & Depression Head in Well 2 is depression head in the well at a time T after the pumping stopped.

How to calculate Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10?

The Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10 formula is defined as the calculation of value of cross-sectional area of well when we have prior information of other parameters used is calculated using Cross-Sectional Area given Specific Capacity = Constant Dependent on Base Soil/((2.303/Time)*log((Depression Head in Well/Depression Head in Well 2),10)). To calculate Cross-sectional Area of Well given Constant Depending upon Soil at Base with Base 10, you need Constant Dependent on Base Soil (K_b), Time (t), Depression Head in Well (h1') & Depression Head in Well 2 (h_w2). With our tool, you need to enter the respective value for Constant Dependent on Base Soil, Time, Depression Head in Well & Depression Head in Well 2 and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search