Correcting Factor for Belt Length given Number of Belts Required Calculator

✖Power transmitted by belt is the amount of power that is transmitted from the belt of a belt drive to the pulley.ⓘ Power transmitted by belt [P_t]			+10% -10%
✖Correction Factor for Industrial Service is the correction factor that is used for industrial purpose.ⓘ Correction Factor for Industrial Service [F_ar]			+10% -10%
✖Number of Belts is the number of belts that are required for a given application.ⓘ Number of Belts [N]			+10% -10%
✖Correction Factor for Arc of Contact is the factor of correction for the arc of contact.ⓘ Correction Factor for Arc of Contact [F_dr]			+10% -10%
✖Power Rating of Single V-Belt is the power rating given to the single V-Belt.ⓘ Power Rating of Single V-Belt [P_r]			+10% -10%

✖Correction Factor for Belt Length is the factor of correction for the belt length.ⓘ Correcting Factor for Belt Length given Number of Belts Required [F_cr]

⎘ Copy

👎

Formula

Reset

👍

Download Design of Belt Drives Formulas PDF PDF Image

Correcting Factor for Belt Length given Number of Belts Required Solution

STEP 0: Pre-Calculation Summary

Formula Used

Correction Factor for Belt Length = Power transmitted by belt*Correction Factor for Industrial Service/(Number of Belts*Correction Factor for Arc of Contact*Power Rating of Single V-Belt)
F_cr = P_t*F_ar/(N*F_dr*P_r)
This formula uses 6 Variables

Variables Used

Correction Factor for Belt Length - Correction Factor for Belt Length is the factor of correction for the belt length.
Power transmitted by belt - (Measured in Watt) - Power transmitted by belt is the amount of power that is transmitted from the belt of a belt drive to the pulley.
Correction Factor for Industrial Service - Correction Factor for Industrial Service is the correction factor that is used for industrial purpose.
Number of Belts - Number of Belts is the number of belts that are required for a given application.
Correction Factor for Arc of Contact - Correction Factor for Arc of Contact is the factor of correction for the arc of contact.
Power Rating of Single V-Belt - (Measured in Watt) - Power Rating of Single V-Belt is the power rating given to the single V-Belt.

STEP 1: Convert Input(s) to Base Unit

Power transmitted by belt: 6.45 Kilowatt --> 6450 Watt (Check conversion here)
Correction Factor for Industrial Service: 1.3 --> No Conversion Required
Number of Belts: 2 --> No Conversion Required
Correction Factor for Arc of Contact: 0.94 --> No Conversion Required
Power Rating of Single V-Belt: 4.128 Kilowatt --> 4128 Watt (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

F_cr = P_t*F_ar/(N*F_dr*P_r) --> 6450*1.3/(2*0.94*4128)

Evaluating ... ...

F_cr = 1.08045212765957

STEP 3: Convert Result to Output's Unit

1.08045212765957 --> No Conversion Required

FINAL ANSWER

1.08045212765957 ≈ 1.080452 <-- Correction Factor for Belt Length

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Mechanical » Machine Design » Design of Belt Drives » V Belt Drives » V Belt Characteristics and Parameters » Correcting Factor for Belt Length given Number of Belts Required

Credits

Created by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has created this Calculator and 1000+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< V Belt Characteristics and Parameters Calculators

Belt Velocity of V-Belt given Belt Tension in Loose Side

Go Belt Velocity = sqrt((Belt Tension on Tight Side-(e^(Coefficient of Friction for Belt Drive*Wrap Angle on Pulley/sin(V belt angle/2)))*Belt Tension on Loose Side)/(Mass of Meter Length of V Belt*(1-(e^(Coefficient of Friction for Belt Drive*Wrap Angle on Pulley/sin(V belt angle/2))))))

Angle of Wrap of V-Belt given Belt Tension in Loose Side of Belt

Go Wrap Angle on Pulley = sin(V belt angle/2)*ln((Belt Tension on Tight Side-Mass of Meter Length of V Belt*Belt Velocity^2)/(Belt Tension on Loose Side-Mass of Meter Length of V Belt*Belt Velocity^2))/Coefficient of Friction for Belt Drive

Belt Tension in Loose Side of V-Belt

Go Belt Tension on Loose Side = (Belt Tension on Tight Side-Mass of Meter Length of V Belt*Belt Velocity^2)/(e^Coefficient of Friction for Belt Drive*Wrap Angle on Pulley/sin(V belt angle/2))+Mass of Meter Length of V Belt*Belt Velocity^2

Belt Tension in Tight Side of V-Belt

Go Belt Tension on Tight Side = (e^Coefficient of Friction for Belt Drive*Wrap Angle on Pulley/sin(V belt angle/2))*(Belt Tension on Loose Side-Mass of Meter Length of V Belt*Belt Velocity^2)+Mass of Meter Length of V Belt*Belt Velocity^2

Correcting Factor for Belt Length given Number of Belts Required Formula

Define Belt?

A belt is a loop of flexible material used to link two or more rotating shafts mechanically, most often parallel. Belts may be used as a source of motion, to transmit power efficiently or to track relative movement.

How to Calculate Correcting Factor for Belt Length given Number of Belts Required?

Correcting Factor for Belt Length given Number of Belts Required calculator uses Correction Factor for Belt Length = Power transmitted by belt*Correction Factor for Industrial Service/(Number of Belts*Correction Factor for Arc of Contact*Power Rating of Single V-Belt) to calculate the Correction Factor for Belt Length, The Correcting Factor for Belt Length given Number of Belts Required formula is defined as the factor of correction for the belt length of a V-Belt drive. Correction Factor for Belt Length is denoted by F_cr symbol.

How to calculate Correcting Factor for Belt Length given Number of Belts Required using this online calculator? To use this online calculator for Correcting Factor for Belt Length given Number of Belts Required, enter Power transmitted by belt (P_t), Correction Factor for Industrial Service (F_ar), Number of Belts (N), Correction Factor for Arc of Contact (F_dr) & Power Rating of Single V-Belt (P_r) and hit the calculate button. Here is how the Correcting Factor for Belt Length given Number of Belts Required calculation can be explained with given input values -> 1.080452 = 6450*1.3/(2*0.94*4128).

FAQ

What is Correcting Factor for Belt Length given Number of Belts Required?

The Correcting Factor for Belt Length given Number of Belts Required formula is defined as the factor of correction for the belt length of a V-Belt drive and is represented as F_cr = P_t*F_ar/(N*F_dr*P_r) or Correction Factor for Belt Length = Power transmitted by belt*Correction Factor for Industrial Service/(Number of Belts*Correction Factor for Arc of Contact*Power Rating of Single V-Belt). Power transmitted by belt is the amount of power that is transmitted from the belt of a belt drive to the pulley, Correction Factor for Industrial Service is the correction factor that is used for industrial purpose, Number of Belts is the number of belts that are required for a given application, Correction Factor for Arc of Contact is the factor of correction for the arc of contact & Power Rating of Single V-Belt is the power rating given to the single V-Belt.

How to calculate Correcting Factor for Belt Length given Number of Belts Required?

The Correcting Factor for Belt Length given Number of Belts Required formula is defined as the factor of correction for the belt length of a V-Belt drive is calculated using Correction Factor for Belt Length = Power transmitted by belt*Correction Factor for Industrial Service/(Number of Belts*Correction Factor for Arc of Contact*Power Rating of Single V-Belt). To calculate Correcting Factor for Belt Length given Number of Belts Required, you need Power transmitted by belt (P_t), Correction Factor for Industrial Service (F_ar), Number of Belts (N), Correction Factor for Arc of Contact (F_dr) & Power Rating of Single V-Belt (P_r). With our tool, you need to enter the respective value for Power transmitted by belt, Correction Factor for Industrial Service, Number of Belts, Correction Factor for Arc of Contact & Power Rating of Single V-Belt and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search