LCM calculator

Constant Depending upon Soil at Base of Well given Specific Capacity Calculator

Engineering Chemistry Financial Health More >>

↳

Civil Chemical Engineering Electrical Electronics More >>

⤿

Environmental Engineering Bridge and Suspension Cable Coastal and Ocean Engineering Columns More >>

⤿

Water Resources Ground Water Conveyance of Water Design of a Chlorination System for Wastewater Disinfection Design of a Circular Settling Tank More >>

⤿

Yield of an Open Well Basic Definitions Characteristic Well Losses Confined Aquifers More >>

⤿

Recuperation Test Constant Level Pumping Test

⤿

Constant Depending upon Base Soil Cross Sectional Area of Well Depression Head after Pumping Stopped Depression Head when Pumping Stopped More >>

⤿

Discharge in Well

✖Cross-Sectional Area given Specific Capacity is the cross-sectional area of the wellbore through which water flows.ⓘ Cross-Sectional Area given Specific Capacity [A_sec]			+10% -10%
✖Specific Capacity in SI Unit is capacity of an open well in SI unit.ⓘ Specific Capacity in SI unit [S_si]			+10% -10%

✖Constant depending on the soil at the base of the well.ⓘ Constant Depending upon Soil at Base of Well given Specific Capacity [K]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Recuperation Test Formulas PDF PDF Image

Constant Depending upon Soil at Base of Well given Specific Capacity Solution

STEP 0: Pre-Calculation Summary

Formula Used

Constant = Cross-Sectional Area given Specific Capacity*Specific Capacity in SI unit
K = A_sec*S_si
This formula uses 3 Variables

Variables Used

Constant - Constant depending on the soil at the base of the well.
Cross-Sectional Area given Specific Capacity - (Measured in Square Meter) - Cross-Sectional Area given Specific Capacity is the cross-sectional area of the wellbore through which water flows.
Specific Capacity in SI unit - (Measured in Meter per Second) - Specific Capacity in SI Unit is capacity of an open well in SI unit.

STEP 1: Convert Input(s) to Base Unit

Cross-Sectional Area given Specific Capacity: 2.495 Square Meter --> 2.495 Square Meter No Conversion Required
Specific Capacity in SI unit: 2 Meter per Second --> 2 Meter per Second No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

K = A_sec*S_si --> 2.495*2

Evaluating ... ...

K = 4.99

STEP 3: Convert Result to Output's Unit

4.99 --> No Conversion Required

FINAL ANSWER

4.99 <-- Constant

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Civil » Environmental Engineering » Water Resources Ground Water » Yield of an Open Well » Recuperation Test » Constant Depending upon Base Soil » Constant Depending upon Soil at Base of Well given Specific Capacity

Credits

Created by Suraj Kumar

Birsa Institute of Technology (BIT), Sindri

Suraj Kumar has created this Calculator and 2100+ more calculators!

Verified by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has verified this Calculator and 2600+ more calculators!

< Constant Depending upon Base Soil Calculators

Constant Depending upon Soil at Base of Well with Base 10

LaTeX Go Constant = ((Cross-Sectional Area given Specific Capacity*2.303)/Time)*log((Depression Head/Depression Head in Well 2),10)

Constant Depending upon Soil at Base of Well

LaTeX Go Constant = (Cross Sectional Area/Time)*log((Depression Head/Depression Head in Well 2),e)

Constant Depending upon Soil at Base of Well given Specific Capacity

LaTeX Go Constant = Cross-Sectional Area given Specific Capacity*Specific Capacity in SI unit

Constant Depending upon Soil at Base of Well given Clay Soil

LaTeX Go Constant = 0.25*Cross Sectional Area

Constant Depending upon Soil at Base of Well given Specific Capacity Formula

LaTeX Go

Constant = Cross-Sectional Area given Specific Capacity*Specific Capacity in SI unit
K = A_sec*S_si

What is Specific Capacity?

Specific Capacity refers to the efficiency of a well in producing water. It is a measure of how much water (in volume) a well can yield per unit of drawdown (or drop in water level) over a specific period of time. The specific capacity is typically expressed in units such as gallons per minute per foot (gpm/ft) or liters per second per meter (L/s/m).

How to Calculate Constant Depending upon Soil at Base of Well given Specific Capacity?

Constant Depending upon Soil at Base of Well given Specific Capacity calculator uses Constant = Cross-Sectional Area given Specific Capacity*Specific Capacity in SI unit to calculate the Constant, The Constant Depending upon Soil at Base of Well given Specific Capacity formula is defined as the calculation of the value of constant depending upon soil when we have prior information of specific capacity. Constant is denoted by K symbol.

How to calculate Constant Depending upon Soil at Base of Well given Specific Capacity using this online calculator? To use this online calculator for Constant Depending upon Soil at Base of Well given Specific Capacity, enter Cross-Sectional Area given Specific Capacity (A_sec) & Specific Capacity in SI unit (S_si) and hit the calculate button. Here is how the Constant Depending upon Soil at Base of Well given Specific Capacity calculation can be explained with given input values -> 4.99 = 2.495*2.

FAQ

What is Constant Depending upon Soil at Base of Well given Specific Capacity?

The Constant Depending upon Soil at Base of Well given Specific Capacity formula is defined as the calculation of the value of constant depending upon soil when we have prior information of specific capacity and is represented as K = A_sec*S_si or Constant = Cross-Sectional Area given Specific Capacity*Specific Capacity in SI unit. Cross-Sectional Area given Specific Capacity is the cross-sectional area of the wellbore through which water flows & Specific Capacity in SI Unit is capacity of an open well in SI unit.

How to calculate Constant Depending upon Soil at Base of Well given Specific Capacity?

The Constant Depending upon Soil at Base of Well given Specific Capacity formula is defined as the calculation of the value of constant depending upon soil when we have prior information of specific capacity is calculated using Constant = Cross-Sectional Area given Specific Capacity*Specific Capacity in SI unit. To calculate Constant Depending upon Soil at Base of Well given Specific Capacity, you need Cross-Sectional Area given Specific Capacity (A_sec) & Specific Capacity in SI unit (S_si). With our tool, you need to enter the respective value for Cross-Sectional Area given Specific Capacity & Specific Capacity in SI unit and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Constant?

In this formula, Constant uses Cross-Sectional Area given Specific Capacity & Specific Capacity in SI unit. We can use 3 other way(s) to calculate the same, which is/are as follows -

Constant = (Cross Sectional Area/Time)*log((Depression Head/Depression Head in Well 2),e)
Constant = ((Cross-Sectional Area given Specific Capacity*2.303)/Time)*log((Depression Head/Depression Head in Well 2),10)
Constant = 0.25*Cross Sectional Area

Home

FREE PDFs

🔍 Search