Constant Depending on Material of Column According to Terms Slenderness Ratio Calculator

✖Compressive yield stress is stress which causes a material to exhibit a specified deformation. Usually determined from the stress-strain diagram obtained in a compression test.ⓘ Compressive Yield Stress [σ_c]			+10% -10%
✖Critical Load On Column is the greatest load that will not cause lateral deflection (buckling).ⓘ Critical Load On Column [P]			+10% -10%
✖Column Cross Sectional Area is the area of a two-dimensional shape that is obtained when a three dimensional shape is sliced perpendicular to some specified axis at a point.ⓘ Column Cross Sectional Area [A_sectional]			+10% -10%
✖The Slenderness ratio is the ratio of the length of a column and the least radius of gyration of its cross section.ⓘ Slenderness Ratio [λ]			+10% -10%

✖Johnson's formula constant is defined as the constant that depends on the material of column.ⓘ Constant Depending on Material of Column According to Terms Slenderness Ratio [r]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Column And Struts Formula PDF PDF Image

Constant Depending on Material of Column According to Terms Slenderness Ratio Solution

STEP 0: Pre-Calculation Summary

Formula Used

Johnson's formula constant = (Compressive Yield Stress-(Critical Load On Column/Column Cross Sectional Area))/(Slenderness Ratio)
r = (σ_c-(P/A_sectional))/(λ)
This formula uses 5 Variables

Variables Used

Johnson's formula constant - Johnson's formula constant is defined as the constant that depends on the material of column.
Compressive Yield Stress - (Measured in Pascal) - Compressive yield stress is stress which causes a material to exhibit a specified deformation. Usually determined from the stress-strain diagram obtained in a compression test.
Critical Load On Column - (Measured in Newton) - Critical Load On Column is the greatest load that will not cause lateral deflection (buckling).
Column Cross Sectional Area - (Measured in Square Meter) - Column Cross Sectional Area is the area of a two-dimensional shape that is obtained when a three dimensional shape is sliced perpendicular to some specified axis at a point.
Slenderness Ratio - The Slenderness ratio is the ratio of the length of a column and the least radius of gyration of its cross section.

STEP 1: Convert Input(s) to Base Unit

Compressive Yield Stress: 420 Newton per Square Meter --> 420 Pascal (Check conversion here)
Critical Load On Column: 5 Newton --> 5 Newton No Conversion Required
Column Cross Sectional Area: 1.4 Square Meter --> 1.4 Square Meter No Conversion Required
Slenderness Ratio: 0.5 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

r = (σ_c-(P/A_sectional))/(λ) --> (420-(5/1.4))/(0.5)

Evaluating ... ...

r = 832.857142857143

STEP 3: Convert Result to Output's Unit

832.857142857143 --> No Conversion Required

FINAL ANSWER

832.857142857143 ≈ 832.8571 <-- Johnson's formula constant

(Calculation completed in 00.007 seconds)

You are here -

Home » Physics » Strength of Materials » Column And Struts » Mechanical » Johnson's Parabolic Formula » Constant Depending on Material of Column According to Terms Slenderness Ratio

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< Johnson's Parabolic Formula Calculators

Constant Depending on Material of Column According to Johnson's Parabolic Formula

LaTeX Go Johnson's formula constant = (Compressive Yield Stress-(Critical Load On Column/Column Cross Sectional Area))/(Effective Column Length/Least Radius of Gyration Column)

Cross-Sectional Area of Column According to Johnson's Parabolic Formula

LaTeX Go Column Cross Sectional Area = Critical Load On Column/(Compressive Yield Stress-(Johnson's formula constant*(Effective Column Length/Least Radius of Gyration Column)))

Critical Load on Column According to Johnson's Parabolic Formula

LaTeX Go Critical Load On Column = (Compressive Yield Stress-(Johnson's formula constant*(Effective Column Length/Least Radius of Gyration Column)))*Column Cross Sectional Area

Compressive Yield Stress According to Johnson's Parabolic Formula

LaTeX Go Compressive Yield Stress = Critical Load On Column/Column Cross Sectional Area+Johnson's formula constant*Effective Column Length/Least Radius of Gyration Column

Constant Depending on Material of Column According to Terms Slenderness Ratio Formula

LaTeX Go

Johnson's formula constant = (Compressive Yield Stress-(Critical Load On Column/Column Cross Sectional Area))/(Slenderness Ratio)
r = (σ_c-(P/A_sectional))/(λ)

What is slenderness ratio in column?

The slenderness ratio of a reinforced concrete (RC) column is the ratio between the length of the column, its lateral dimensions, and end fixity. The slenderness ratio is calculated by dividing the column length by its radius of gyration. The slenderness ratio differentiates the short column from the long or slender column.

How to Calculate Constant Depending on Material of Column According to Terms Slenderness Ratio?

Constant Depending on Material of Column According to Terms Slenderness Ratio calculator uses Johnson's formula constant = (Compressive Yield Stress-(Critical Load On Column/Column Cross Sectional Area))/(Slenderness Ratio) to calculate the Johnson's formula constant, Constant Depending on Material of Column According to Terms Slenderness Ratio formula is defined as a measure of the constant value that depends on the material properties of a column and its slenderness ratio, which is a critical parameter in determining the column's stability and load-carrying capacity in structural engineering. Johnson's formula constant is denoted by r symbol.

How to calculate Constant Depending on Material of Column According to Terms Slenderness Ratio using this online calculator? To use this online calculator for Constant Depending on Material of Column According to Terms Slenderness Ratio, enter Compressive Yield Stress (σ_c), Critical Load On Column (P), Column Cross Sectional Area (A_sectional) & Slenderness Ratio (λ) and hit the calculate button. Here is how the Constant Depending on Material of Column According to Terms Slenderness Ratio calculation can be explained with given input values -> 832.8571 = (420-(5/1.4))/(0.5).

FAQ

What is Constant Depending on Material of Column According to Terms Slenderness Ratio?

Constant Depending on Material of Column According to Terms Slenderness Ratio formula is defined as a measure of the constant value that depends on the material properties of a column and its slenderness ratio, which is a critical parameter in determining the column's stability and load-carrying capacity in structural engineering and is represented as r = (σ_c-(P/A_sectional))/(λ) or Johnson's formula constant = (Compressive Yield Stress-(Critical Load On Column/Column Cross Sectional Area))/(Slenderness Ratio). Compressive yield stress is stress which causes a material to exhibit a specified deformation. Usually determined from the stress-strain diagram obtained in a compression test, Critical Load On Column is the greatest load that will not cause lateral deflection (buckling), Column Cross Sectional Area is the area of a two-dimensional shape that is obtained when a three dimensional shape is sliced perpendicular to some specified axis at a point & The Slenderness ratio is the ratio of the length of a column and the least radius of gyration of its cross section.

How to calculate Constant Depending on Material of Column According to Terms Slenderness Ratio?

Constant Depending on Material of Column According to Terms Slenderness Ratio formula is defined as a measure of the constant value that depends on the material properties of a column and its slenderness ratio, which is a critical parameter in determining the column's stability and load-carrying capacity in structural engineering is calculated using Johnson's formula constant = (Compressive Yield Stress-(Critical Load On Column/Column Cross Sectional Area))/(Slenderness Ratio). To calculate Constant Depending on Material of Column According to Terms Slenderness Ratio, you need Compressive Yield Stress (σ_c), Critical Load On Column (P), Column Cross Sectional Area (A_sectional) & Slenderness Ratio (λ). With our tool, you need to enter the respective value for Compressive Yield Stress, Critical Load On Column, Column Cross Sectional Area & Slenderness Ratio and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Johnson's formula constant?

In this formula, Johnson's formula constant uses Compressive Yield Stress, Critical Load On Column, Column Cross Sectional Area & Slenderness Ratio. We can use 1 other way(s) to calculate the same, which is/are as follows -

Johnson's formula constant = (Compressive Yield Stress-(Critical Load On Column/Column Cross Sectional Area))/(Effective Column Length/Least Radius of Gyration Column)

Home

FREE PDFs

🔍 Search