Component of Strain at Level of First Tendon due to Bending Calculator

✖Change in Length Dimension is produced when a force is applied to a wire or rod parallel to its length L0, either stretching it (a tension) or compressing it.ⓘ Change in Length Dimension [ΔL]			+10% -10%
✖Length of Beam in Prestress is the center to center distance between the supports or the effective length of the beam.ⓘ Length of Beam in Prestress [L]			+10% -10%

✖Strain due to Bending is the strain in the level of tendon A due to bending action.ⓘ Component of Strain at Level of First Tendon due to Bending [ε_c2]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Loss due to Elastic Shortening Formulas PDF PDF Image

Component of Strain at Level of First Tendon due to Bending Solution

STEP 0: Pre-Calculation Summary

Formula Used

Strain due to Bending = Change in Length Dimension/Length of Beam in Prestress
ε_c2 = ΔL/L
This formula uses 3 Variables

Variables Used

Strain due to Bending - Strain due to Bending is the strain in the level of tendon A due to bending action.
Change in Length Dimension - (Measured in Meter) - Change in Length Dimension is produced when a force is applied to a wire or rod parallel to its length L0, either stretching it (a tension) or compressing it.
Length of Beam in Prestress - (Measured in Meter) - Length of Beam in Prestress is the center to center distance between the supports or the effective length of the beam.

STEP 1: Convert Input(s) to Base Unit

Change in Length Dimension: 0.3 Meter --> 0.3 Meter No Conversion Required
Length of Beam in Prestress: 10.2 Meter --> 10.2 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

ε_c2 = ΔL/L --> 0.3/10.2

Evaluating ... ...

ε_c2 = 0.0294117647058824

STEP 3: Convert Result to Output's Unit

0.0294117647058824 --> No Conversion Required

FINAL ANSWER

0.0294117647058824 ≈ 0.029412 <-- Strain due to Bending

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Structural Engineering » Prestressed Concrete » Losses of Prestress » Loss due to Elastic Shortening » Post Tensioned Members » Component of Strain at Level of First Tendon due to Bending

Credits

Created by Chandana P Dev

NSS College of Engineering (NSSCE), Palakkad

Chandana P Dev has created this Calculator and 500+ more calculators!

Verified by Rithik Agrawal

National Institute of Technology Karnataka (NITK), Surathkal

Rithik Agrawal has verified this Calculator and 400+ more calculators!

< Post Tensioned Members Calculators

Prestress Drop given Stress in concrete at Same Level due to Prestressing Force

LaTeX Go Prestress Drop = Modulus of Elasticity of Steel Reinforcement*Stress in Concrete Section/Modulus of Elasticity Concrete

Area of Concrete Section given Prestress Drop

LaTeX Go Concrete Occupied Area = Modular Ratio for Elastic Shortening*Prestress Force/(Prestress Drop)

Prestress Drop given Modular Ratio

LaTeX Go Prestress Drop = Modular Ratio for Elastic Shortening*Stress in Concrete Section

Prestress Drop

LaTeX Go Prestress Drop = Modulus of Elasticity of Steel Reinforcement*Change in Strain

Component of Strain at Level of First Tendon due to Bending Formula

LaTeX Go

Strain due to Bending = Change in Length Dimension/Length of Beam in Prestress
ε_c2 = ΔL/L

What are the various Systems of Prestresisng?

1 Pre-tensioning: In this system the tendons are first tensioned between rigid anchors.
2 Post tensioning: In this system the concrete units are first cast by incorporating ducts on groves to house the tendons.
3 Thermo electric prestressing: In this system, the method of prestressing by heated tendons, anchored by passing electric current in the high tensile wires.
4 Chemical Prestressing: In this system, the method is made possible by the development of expanding cement (calcium-sulpho aluminates). The expansion of concrete is restrained by high tensile steel wires.

How to Calculate Component of Strain at Level of First Tendon due to Bending?

Component of Strain at Level of First Tendon due to Bending calculator uses Strain due to Bending = Change in Length Dimension/Length of Beam in Prestress to calculate the Strain due to Bending, The Component of Strain at Level of First Tendon due to Bending is defined as the ration between change in length of the beam to original length of beam. Strain due to Bending is denoted by ε_c2 symbol.

How to calculate Component of Strain at Level of First Tendon due to Bending using this online calculator? To use this online calculator for Component of Strain at Level of First Tendon due to Bending, enter Change in Length Dimension (ΔL) & Length of Beam in Prestress (L) and hit the calculate button. Here is how the Component of Strain at Level of First Tendon due to Bending calculation can be explained with given input values -> 0.03 = 0.3/10.2.

FAQ

What is Component of Strain at Level of First Tendon due to Bending?

The Component of Strain at Level of First Tendon due to Bending is defined as the ration between change in length of the beam to original length of beam and is represented as ε_c2 = ΔL/L or Strain due to Bending = Change in Length Dimension/Length of Beam in Prestress. Change in Length Dimension is produced when a force is applied to a wire or rod parallel to its length L0, either stretching it (a tension) or compressing it & Length of Beam in Prestress is the center to center distance between the supports or the effective length of the beam.

How to calculate Component of Strain at Level of First Tendon due to Bending?

The Component of Strain at Level of First Tendon due to Bending is defined as the ration between change in length of the beam to original length of beam is calculated using Strain due to Bending = Change in Length Dimension/Length of Beam in Prestress. To calculate Component of Strain at Level of First Tendon due to Bending, you need Change in Length Dimension (ΔL) & Length of Beam in Prestress (L). With our tool, you need to enter the respective value for Change in Length Dimension & Length of Beam in Prestress and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search