Coefficient of Friction of Screw Thread given Load Calculator

✖Effort in lowering load is the force required to overcome the resistance to lower the load.ⓘ Effort in lowering load [P_lo]			+10% -10%
✖Helix angle of screw is defined as the angle subtended between this unwound circumferential line and the pitch of the helix.ⓘ Helix angle of screw [α]			+10% -10%
✖Load on screw is defined as the weight (force) of the body that is acted upon the screw threads.ⓘ Load on screw [W]			+10% -10%

✖Coefficient of friction at screw thread is the ratio defining the force that resists the motion of the nut in relation to the threads in contact with it.ⓘ Coefficient of Friction of Screw Thread given Load [μ]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Power Screws Formulas PDF PDF Image

Coefficient of Friction of Screw Thread given Load Solution

STEP 0: Pre-Calculation Summary

Formula Used

Coefficient of friction at screw thread = (Effort in lowering load+tan(Helix angle of screw)*Load on screw)/(Load on screw-Effort in lowering load*tan(Helix angle of screw))
μ = (P_lo+tan(α)*W)/(W-P_lo*tan(α))
This formula uses 1 Functions, 4 Variables

Functions Used

tan - The tangent of an angle is a trigonometric ratio of the length of the side opposite an angle to the length of the side adjacent to an angle in a right triangle., tan(Angle)

Variables Used

Coefficient of friction at screw thread - Coefficient of friction at screw thread is the ratio defining the force that resists the motion of the nut in relation to the threads in contact with it.
Effort in lowering load - (Measured in Newton) - Effort in lowering load is the force required to overcome the resistance to lower the load.
Helix angle of screw - (Measured in Radian) - Helix angle of screw is defined as the angle subtended between this unwound circumferential line and the pitch of the helix.
Load on screw - (Measured in Newton) - Load on screw is defined as the weight (force) of the body that is acted upon the screw threads.

STEP 1: Convert Input(s) to Base Unit

Effort in lowering load: 120 Newton --> 120 Newton No Conversion Required
Helix angle of screw: 4.5 Degree --> 0.0785398163397301 Radian (Check conversion here)
Load on screw: 1700 Newton --> 1700 Newton No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

μ = (P_lo+tan(α)*W)/(W-P_lo*tan(α)) --> (120+tan(0.0785398163397301)*1700)/(1700-120*tan(0.0785398163397301))

Evaluating ... ...

μ = 0.150123942862617

STEP 3: Convert Result to Output's Unit

0.150123942862617 --> No Conversion Required

FINAL ANSWER

0.150123942862617 ≈ 0.150124 <-- Coefficient of friction at screw thread

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Mechanical » Machine Design » Power Screws » Torque Requirement in Lowering Load using Square threaded Screws » Coefficient of Friction of Screw Thread given Load

Credits

Created by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has created this Calculator and 1000+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< Torque Requirement in Lowering Load using Square threaded Screws Calculators

Coefficient of Friction of Screw Thread given Load

LaTeX Go Coefficient of friction at screw thread = (Effort in lowering load+tan(Helix angle of screw)*Load on screw)/(Load on screw-Effort in lowering load*tan(Helix angle of screw))

Helix Angle of Power Screw given Effort Required in Lowering Load

LaTeX Go Helix angle of screw = atan((Load on screw*Coefficient of friction at screw thread-Effort in lowering load)/(Coefficient of friction at screw thread*Effort in lowering load+Load on screw))

Load on power Screw given Effort Required in Lowering Load

LaTeX Go Load on screw = Effort in lowering load/((Coefficient of friction at screw thread-tan(Helix angle of screw))/(1+Coefficient of friction at screw thread*tan(Helix angle of screw)))

Effort Required in Lowering Load

LaTeX Go Effort in lowering load = Load on screw*((Coefficient of friction at screw thread-tan(Helix angle of screw))/(1+Coefficient of friction at screw thread*tan(Helix angle of screw)))

Coefficient of Friction of Screw Thread given Load Formula

LaTeX Go

Define Coefficient of Friction?

Coefficient of friction is Defined as the ratio of the tangential force that is needed to start or to maintain uniform relative motion between two contacting surfaces to the perpendicular force holding them in contact, the ratio usually being larger for starting than for moving friction

How to Calculate Coefficient of Friction of Screw Thread given Load?

Coefficient of Friction of Screw Thread given Load calculator uses Coefficient of friction at screw thread = (Effort in lowering load+tan(Helix angle of screw)*Load on screw)/(Load on screw-Effort in lowering load*tan(Helix angle of screw)) to calculate the Coefficient of friction at screw thread, Coefficient of Friction of Screw Thread given Load formula is defined as the ratio of the tangential force that is needed to start or to maintain uniform relative motion between two contacting surfaces to the perpendicular force holding them in contact, the ratio usually being larger for starting than for moving friction. Coefficient of friction at screw thread is denoted by μ symbol.

How to calculate Coefficient of Friction of Screw Thread given Load using this online calculator? To use this online calculator for Coefficient of Friction of Screw Thread given Load, enter Effort in lowering load (P_lo), Helix angle of screw (α) & Load on screw (W) and hit the calculate button. Here is how the Coefficient of Friction of Screw Thread given Load calculation can be explained with given input values -> 0.150124 = (120+tan(0.0785398163397301)*1700)/(1700-120*tan(0.0785398163397301)).

FAQ

What is Coefficient of Friction of Screw Thread given Load?

Coefficient of Friction of Screw Thread given Load formula is defined as the ratio of the tangential force that is needed to start or to maintain uniform relative motion between two contacting surfaces to the perpendicular force holding them in contact, the ratio usually being larger for starting than for moving friction and is represented as μ = (P_lo+tan(α)*W)/(W-P_lo*tan(α)) or Coefficient of friction at screw thread = (Effort in lowering load+tan(Helix angle of screw)*Load on screw)/(Load on screw-Effort in lowering load*tan(Helix angle of screw)). Effort in lowering load is the force required to overcome the resistance to lower the load, Helix angle of screw is defined as the angle subtended between this unwound circumferential line and the pitch of the helix & Load on screw is defined as the weight (force) of the body that is acted upon the screw threads.

How to calculate Coefficient of Friction of Screw Thread given Load?

Coefficient of Friction of Screw Thread given Load formula is defined as the ratio of the tangential force that is needed to start or to maintain uniform relative motion between two contacting surfaces to the perpendicular force holding them in contact, the ratio usually being larger for starting than for moving friction is calculated using Coefficient of friction at screw thread = (Effort in lowering load+tan(Helix angle of screw)*Load on screw)/(Load on screw-Effort in lowering load*tan(Helix angle of screw)). To calculate Coefficient of Friction of Screw Thread given Load, you need Effort in lowering load (P_lo), Helix angle of screw (α) & Load on screw (W). With our tool, you need to enter the respective value for Effort in lowering load, Helix angle of screw & Load on screw and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Coefficient of friction at screw thread?

In this formula, Coefficient of friction at screw thread uses Effort in lowering load, Helix angle of screw & Load on screw. We can use 1 other way(s) to calculate the same, which is/are as follows -

Coefficient of friction at screw thread = (2*Torque for lowering load+Load on screw*Mean Diameter of Power Screw*tan(Helix angle of screw))/(Load on screw*Mean Diameter of Power Screw-2*Torque for lowering load*tan(Helix angle of screw))

Home

FREE PDFs

🔍 Search