Capacitance responsible for given overcut Calculator

✖Overcut in mm per side is the overcut produced during EDM.ⓘ Overcut in mm per side [O]			+10% -10%
✖Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it.ⓘ Overcut Constant B [B]			+10% -10%
✖Overcut Constant A is an empirical constant used in overcut calculations of EDM, its different for different materials at different voltages passing through it.ⓘ Overcut Constant A [A]			+10% -10%

✖Capacitance in Surface Defect is the ability of a component or circuit to store and collect energy in the form of an electrical charge.ⓘ Capacitance responsible for given overcut [C_sd]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Unconventional machining processes Formula PDF PDF Image

Capacitance responsible for given overcut Solution

STEP 0: Pre-Calculation Summary

Formula Used

Capacitance in Surface Defect = ((Overcut in mm per side-Overcut Constant B)/Overcut Constant A)^(1/0.333)
C_sd = ((O-B)/A)^(1/0.333)
This formula uses 4 Variables

Variables Used

Capacitance in Surface Defect - (Measured in Farad) - Capacitance in Surface Defect is the ability of a component or circuit to store and collect energy in the form of an electrical charge.
Overcut in mm per side - Overcut in mm per side is the overcut produced during EDM.
Overcut Constant B - (Measured in Meter) - Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it.
Overcut Constant A - (Measured in Meter) - Overcut Constant A is an empirical constant used in overcut calculations of EDM, its different for different materials at different voltages passing through it.

STEP 1: Convert Input(s) to Base Unit

Overcut in mm per side: 5 --> No Conversion Required
Overcut Constant B: 2.5 Meter --> 2.5 Meter No Conversion Required
Overcut Constant A: 1.4 Meter --> 1.4 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

C_sd = ((O-B)/A)^(1/0.333) --> ((5-2.5)/1.4)^(1/0.333)

Evaluating ... ...

C_sd = 5.70416541457262

STEP 3: Convert Result to Output's Unit

5.70416541457262 Farad -->5704165.41457262 Microfarad (Check conversion here)

FINAL ANSWER

5704165.41457262 ≈ 5.7E+6 Microfarad <-- Capacitance in Surface Defect

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » Possible surface defects in EDM » Overcut » Capacitance responsible for given overcut

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Vaibhav Malani

National Institute of Technology (NIT), Tiruchirapalli

Vaibhav Malani has verified this Calculator and 200+ more calculators!

< Overcut Calculators

Capacitance responsible for given overcut

LaTeX Go Capacitance in Surface Defect = ((Overcut in mm per side-Overcut Constant B)/Overcut Constant A)^(1/0.333)

Overcut produced per side

LaTeX Go Overcut in mm per side = (Overcut Constant A*Capacitance in Surface Defect^0.333)+Overcut Constant B

Overcut constant A

LaTeX Go Overcut Constant A = (Overcut in mm per side-Overcut Constant B)/Capacitance in Surface Defect^0.333

Overcut constant B

LaTeX Go Overcut Constant B = Overcut in mm per side-(Overcut Constant A*Capacitance in Surface Defect^0.333)

Capacitance responsible for given overcut Formula

LaTeX Go

Capacitance in Surface Defect = ((Overcut in mm per side-Overcut Constant B)/Overcut Constant A)^(1/0.333)
C_sd = ((O-B)/A)^(1/0.333)

What factors affects surface finish during EDM ?

The amount of material removed and the surface finish produced is dependent upon the current in the spark. The material removed by the spark can be assumed to be a crater. The amount removed therefore will depend upon the crater depth, which is directly proportional to the current. Thus as the material removed increases and at the same time, the surface finish also decreases. However, decreasing the current in the spark, but increasing its frequency will improve the surface finish in view of the small crater size, but at the same time, the material removal rate can be maintained by increasing the frequency.

How to Calculate Capacitance responsible for given overcut?

Capacitance responsible for given overcut calculator uses Capacitance in Surface Defect = ((Overcut in mm per side-Overcut Constant B)/Overcut Constant A)^(1/0.333) to calculate the Capacitance in Surface Defect, Capacitance responsible for given overcut formula is defined as the minimum capacitance that will create the given overcut due to side sparks in EDM. Capacitance in Surface Defect is denoted by C_sd symbol.

How to calculate Capacitance responsible for given overcut using this online calculator? To use this online calculator for Capacitance responsible for given overcut, enter Overcut in mm per side (O), Overcut Constant B (B) & Overcut Constant A (A) and hit the calculate button. Here is how the Capacitance responsible for given overcut calculation can be explained with given input values -> 5.7E+12 = ((5-2.5)/1.4)^(1/0.333).

FAQ

What is Capacitance responsible for given overcut?

Capacitance responsible for given overcut formula is defined as the minimum capacitance that will create the given overcut due to side sparks in EDM and is represented as C_sd = ((O-B)/A)^(1/0.333) or Capacitance in Surface Defect = ((Overcut in mm per side-Overcut Constant B)/Overcut Constant A)^(1/0.333). Overcut in mm per side is the overcut produced during EDM, Overcut Constant B is an empirical constant used to calculate overcut produced in the EDM process its different for different materials at different voltages passing through it & Overcut Constant A is an empirical constant used in overcut calculations of EDM, its different for different materials at different voltages passing through it.

How to calculate Capacitance responsible for given overcut?

Capacitance responsible for given overcut formula is defined as the minimum capacitance that will create the given overcut due to side sparks in EDM is calculated using Capacitance in Surface Defect = ((Overcut in mm per side-Overcut Constant B)/Overcut Constant A)^(1/0.333). To calculate Capacitance responsible for given overcut, you need Overcut in mm per side (O), Overcut Constant B (B) & Overcut Constant A (A). With our tool, you need to enter the respective value for Overcut in mm per side, Overcut Constant B & Overcut Constant A and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search