Bulk Modulus given Volume Stress and Strain Calculator

✖Volume Stress is the force per unit area acting on the body immersed in a liquid.ⓘ Volume Stress [VS]			+10% -10%
✖The Volumetric Strain is the ratio of change in volume to original volume.ⓘ Volumetric Strain [ε_v]			+10% -10%

✖Bulk Modulus given Volume Stress and Strain is defined as the ratio of the volume stress (change in pressure applied to a material) to the volume strain (relative change in the material’s volume).ⓘ Bulk Modulus given Volume Stress and Strain [k_v]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Fluid Mechanics Basics Formulas PDF PDF Image

Bulk Modulus given Volume Stress and Strain Solution

STEP 0: Pre-Calculation Summary

Formula Used

Bulk Modulus given Volume Stress and Strain = Volume Stress/Volumetric Strain
k_v = VS/ε_v
This formula uses 3 Variables

Variables Used

Bulk Modulus given Volume Stress and Strain - (Measured in Pascal) - Bulk Modulus given Volume Stress and Strain is defined as the ratio of the volume stress (change in pressure applied to a material) to the volume strain (relative change in the material’s volume).
Volume Stress - (Measured in Pascal) - Volume Stress is the force per unit area acting on the body immersed in a liquid.
Volumetric Strain - The Volumetric Strain is the ratio of change in volume to original volume.

STEP 1: Convert Input(s) to Base Unit

Volume Stress: 11 Pascal --> 11 Pascal No Conversion Required
Volumetric Strain: 30 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

k_v = VS/ε_v --> 11/30

Evaluating ... ...

k_v = 0.366666666666667

STEP 3: Convert Result to Output's Unit

0.366666666666667 Pascal --> No Conversion Required

FINAL ANSWER

0.366666666666667 ≈ 0.366667 Pascal <-- Bulk Modulus given Volume Stress and Strain

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Mechanical » Fluid Mechanics » Introduction to Fluid Mechanics Basics » Fluid Mechanics Basics » Bulk Modulus given Volume Stress and Strain

Credits

Created by Anirudh Singh

National Institute of Technology (NIT), Jamshedpur

Anirudh Singh has created this Calculator and 300+ more calculators!

Verified by Team Softusvista

Softusvista Office (Pune), India

Team Softusvista has verified this Calculator and 1100+ more calculators!

< Fluid Mechanics Basics Calculators

Equation of Continuity for Compressible Fluids

LaTeX Go Velocity of the fluid at 1 = (Cross-Sectional Area at Point 2*Velocity of the fluid at 2*Density at Point 2)/(Cross-Sectional Area at Point 1*Density at Point 1)

Equation of Continuity for Incompressible Fluids

LaTeX Go Velocity of the fluid at 1 = (Cross-Sectional Area at Point 2*Velocity of the fluid at 2)/Cross-Sectional Area at Point 1

Cavitation Number

LaTeX Go Cavitation Number = (Pressure-Vapour Pressure)/(Mass Density*(Fluid Velocity^2)/2)

Bulk Modulus given Volume Stress and Strain

LaTeX Go Bulk Modulus given Volume Stress and Strain = Volume Stress/Volumetric Strain

< Stress and Strain Calculators

Elongation Circular Tapered Bar

LaTeX Go Elongation in Circular Tapered Bar = (4*Load*Length of Bar)/(pi*Diameter of Bigger End*Diameter of Smaller End*Elastic Modulus)

Moment of Inertia for Hollow Circular Shaft

LaTeX Go Moment of Inertia for Hollow Circular Shaft = pi/32*(Outer Diameter of Hollow Circular Section^(4)-Inner Diameter of Hollow Circular Section^(4))

Elongation of Prismatic Bar due to its Own Weight

LaTeX Go Elongation of Prismatic Bar = (Load*Length of Bar)/(2*Area of Prismatic Bar*Elastic Modulus)

Moment of Inertia about Polar Axis

LaTeX Go Polar Moment of Inertia = (pi*Diameter of Shaft^(4))/32

Bulk Modulus given Volume Stress and Strain Formula

LaTeX Go

Bulk Modulus given Volume Stress and Strain = Volume Stress/Volumetric Strain
k_v = VS/ε_v

What are the Factors affecting Bulk Modulus of a Substance?

Material Composition: Different materials inherently have different bulk moduli. Metals, for example, tend to have high bulk moduli due to strong atomic bonds, while gases have low bulk moduli because their molecules are widely spaced,
Temperature: Typically, as temperature increases, materials become more compressible (bulk modulus decreases). In gases, higher temperatures increase molecular movement, decreasing resistance to compression.

How to Calculate Bulk Modulus given Volume Stress and Strain?

Bulk Modulus given Volume Stress and Strain calculator uses Bulk Modulus given Volume Stress and Strain = Volume Stress/Volumetric Strain to calculate the Bulk Modulus given Volume Stress and Strain, Bulk Modulus given Volume Stress and Strain formula is defined as a measure of a material's resistance to uniform compression. It quantifies how much a material will deform under applied pressure, reflecting its elasticity and ability to return to its original shape after the stress is removed. Bulk Modulus given Volume Stress and Strain is denoted by k_v symbol.

How to calculate Bulk Modulus given Volume Stress and Strain using this online calculator? To use this online calculator for Bulk Modulus given Volume Stress and Strain, enter Volume Stress (VS) & Volumetric Strain (ε_v) and hit the calculate button. Here is how the Bulk Modulus given Volume Stress and Strain calculation can be explained with given input values -> 0.366667 = 11/30.

FAQ

What is Bulk Modulus given Volume Stress and Strain?

Bulk Modulus given Volume Stress and Strain formula is defined as a measure of a material's resistance to uniform compression. It quantifies how much a material will deform under applied pressure, reflecting its elasticity and ability to return to its original shape after the stress is removed and is represented as k_v = VS/ε_v or Bulk Modulus given Volume Stress and Strain = Volume Stress/Volumetric Strain. Volume Stress is the force per unit area acting on the body immersed in a liquid & The Volumetric Strain is the ratio of change in volume to original volume.

How to calculate Bulk Modulus given Volume Stress and Strain?

Bulk Modulus given Volume Stress and Strain formula is defined as a measure of a material's resistance to uniform compression. It quantifies how much a material will deform under applied pressure, reflecting its elasticity and ability to return to its original shape after the stress is removed is calculated using Bulk Modulus given Volume Stress and Strain = Volume Stress/Volumetric Strain. To calculate Bulk Modulus given Volume Stress and Strain, you need Volume Stress (VS) & Volumetric Strain (ε_v). With our tool, you need to enter the respective value for Volume Stress & Volumetric Strain and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search