Bolt Load in Design of Flange for Gasket Seating Calculator

✖The Greater Cross-section Area of Bolts is defined as the area of the cross-section of the gasket bolt taking the greater of the given value.ⓘ Greater Cross-section Area of Bolts [A_m]			+10% -10%
✖Actual Bolt Area is defined as cross-sectional area of the bolts using root diameter of thread or least diameter of an unthreaded portion (if less), to prevent damage to the gasket during bolting-up.ⓘ Actual Bolt Area [A_b]			+10% -10%
✖The Stress Required for Gasket Seating is defined as the value of the stress in the gasket required for the seating or the installment of the gasket.ⓘ Stress Required for Gasket Seating [σ_gs]			+10% -10%

✖Bolt Load Under Operating Condition for Gasket is defined as the load acting on a bolt, it is limited to the amount of load the bolt can handle before failing.ⓘ Bolt Load in Design of Flange for Gasket Seating [W_m1]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Bolt Loads in Gasket Joints Formulas PDF PDF Image

Bolt Load in Design of Flange for Gasket Seating Solution

STEP 0: Pre-Calculation Summary

Formula Used

Bolt Load Under Operating Condition for Gasket = ((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)*Stress Required for Gasket Seating
W_m1 = ((A_m+A_b)/2)*σ_gs
This formula uses 4 Variables

Variables Used

Bolt Load Under Operating Condition for Gasket - (Measured in Newton) - Bolt Load Under Operating Condition for Gasket is defined as the load acting on a bolt, it is limited to the amount of load the bolt can handle before failing.
Greater Cross-section Area of Bolts - (Measured in Square Meter) - The Greater Cross-section Area of Bolts is defined as the area of the cross-section of the gasket bolt taking the greater of the given value.
Actual Bolt Area - (Measured in Square Meter) - Actual Bolt Area is defined as cross-sectional area of the bolts using root diameter of thread or least diameter of an unthreaded portion (if less), to prevent damage to the gasket during bolting-up.
Stress Required for Gasket Seating - (Measured in Pascal) - The Stress Required for Gasket Seating is defined as the value of the stress in the gasket required for the seating or the installment of the gasket.

STEP 1: Convert Input(s) to Base Unit

Greater Cross-section Area of Bolts: 1120 Square Millimeter --> 0.00112 Square Meter (Check conversion here)
Actual Bolt Area: 126 Square Millimeter --> 0.000126 Square Meter (Check conversion here)
Stress Required for Gasket Seating: 25.06 Newton per Square Millimeter --> 25060000 Pascal (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

W_m1 = ((A_m+A_b)/2)*σ_gs --> ((0.00112+0.000126)/2)*25060000

Evaluating ... ...

W_m1 = 15612.38

STEP 3: Convert Result to Output's Unit

15612.38 Newton --> No Conversion Required

FINAL ANSWER

15612.38 Newton <-- Bolt Load Under Operating Condition for Gasket

(Calculation completed in 00.020 seconds)

You are here -

Home » Physics » Design of Machine Elements » Design of Coupling » Packing » Mechanical » Bolt Loads in Gasket Joints » Bolt Load in Design of Flange for Gasket Seating

Credits

Created by sanjay shiva

national institute of technology hamirpur (NITH ), hamirpur , himachal pradesh

sanjay shiva has created this Calculator and 100+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< Bolt Loads in Gasket Joints Calculators

Bolt Load under operating condition given Hydrostatic End Force

LaTeX Go Bolt Load Under Operating Condition for Gasket = ((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)+(2*Width of u-collar in Gasket*pi*Gasket Diameter*Pressure at Outer Diameter of Gasket*Gasket Factor)

Hydrostatic End Force given Bolt Load under Operating condition

LaTeX Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-(2*Width of u-collar in Gasket*pi*Gasket Diameter*Gasket Factor*Pressure at Outer Diameter of Gasket)

Bolt load under operating condition

LaTeX Go Bolt Load Under Operating Condition for Gasket = Hydrostatic End Force in Gasket Seal+Total Joint Surface Compression Load

Hydrostatic end force

LaTeX Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-Total Joint Surface Compression Load

Bolt Load in Design of Flange for Gasket Seating Formula

LaTeX Go

Bolt Load Under Operating Condition for Gasket = ((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)*Stress Required for Gasket Seating
W_m1 = ((A_m+A_b)/2)*σ_gs

What is Bolt load?

Bolt load is when a load is placed on a bolt, it is limited to the amount of load the bolt can handle before failing.

How to Calculate Bolt Load in Design of Flange for Gasket Seating?

Bolt Load in Design of Flange for Gasket Seating calculator uses Bolt Load Under Operating Condition for Gasket = ((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)*Stress Required for Gasket Seating to calculate the Bolt Load Under Operating Condition for Gasket, The Bolt Load in Design of Flange for Gasket Seating formula is defined as when a load is placed on a bolt, it is limited to the amount of load the bolt can handle before failing. Bolt Load Under Operating Condition for Gasket is denoted by W_m1 symbol.

How to calculate Bolt Load in Design of Flange for Gasket Seating using this online calculator? To use this online calculator for Bolt Load in Design of Flange for Gasket Seating, enter Greater Cross-section Area of Bolts (A_m), Actual Bolt Area (A_b) & Stress Required for Gasket Seating (σ_gs) and hit the calculate button. Here is how the Bolt Load in Design of Flange for Gasket Seating calculation can be explained with given input values -> 15612.38 = ((0.00112+0.000126)/2)*25060000.

FAQ

What is Bolt Load in Design of Flange for Gasket Seating?

The Bolt Load in Design of Flange for Gasket Seating formula is defined as when a load is placed on a bolt, it is limited to the amount of load the bolt can handle before failing and is represented as W_m1 = ((A_m+A_b)/2)*σ_gs or Bolt Load Under Operating Condition for Gasket = ((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)*Stress Required for Gasket Seating. The Greater Cross-section Area of Bolts is defined as the area of the cross-section of the gasket bolt taking the greater of the given value, Actual Bolt Area is defined as cross-sectional area of the bolts using root diameter of thread or least diameter of an unthreaded portion (if less), to prevent damage to the gasket during bolting-up & The Stress Required for Gasket Seating is defined as the value of the stress in the gasket required for the seating or the installment of the gasket.

How to calculate Bolt Load in Design of Flange for Gasket Seating?

The Bolt Load in Design of Flange for Gasket Seating formula is defined as when a load is placed on a bolt, it is limited to the amount of load the bolt can handle before failing is calculated using Bolt Load Under Operating Condition for Gasket = ((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)*Stress Required for Gasket Seating. To calculate Bolt Load in Design of Flange for Gasket Seating, you need Greater Cross-section Area of Bolts (A_m), Actual Bolt Area (A_b) & Stress Required for Gasket Seating (σ_gs). With our tool, you need to enter the respective value for Greater Cross-section Area of Bolts, Actual Bolt Area & Stress Required for Gasket Seating and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Bolt Load Under Operating Condition for Gasket?

In this formula, Bolt Load Under Operating Condition for Gasket uses Greater Cross-section Area of Bolts, Actual Bolt Area & Stress Required for Gasket Seating. We can use 2 other way(s) to calculate the same, which is/are as follows -

Bolt Load Under Operating Condition for Gasket = Hydrostatic End Force in Gasket Seal+Total Joint Surface Compression Load
Bolt Load Under Operating Condition for Gasket = ((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)+(2*Width of u-collar in Gasket*pi*Gasket Diameter*Pressure at Outer Diameter of Gasket*Gasket Factor)

Home

FREE PDFs

🔍 Search