Bearing Capacity Factor Dependent on Unit Weight for Strip Footing Calculator

✖Ultimate Bearing Capacity in Soil is defined as the minimum gross pressure intensity at the base of the foundation at which the soil fails in shear.ⓘ Ultimate Bearing Capacity in Soil [q_fc]			+10% -10%
✖Effective Surcharge in KiloPascal also called as surcharge load refers to the vertical pressure or any load that acts over the ground surface additional to basic earth pressure.ⓘ Effective Surcharge in KiloPascal [σ_s]			+10% -10%
✖Bearing Capacity Factor dependent on Surcharge is a constant whose value depends upon surcharge.ⓘ Bearing Capacity Factor dependent on Surcharge [N_q]			+10% -10%
✖Unit Weight of Soil mass is the ratio of the total weight of soil to the total volume of soil.ⓘ Unit Weight of Soil [γ]			+10% -10%
✖Width of Footing is the shorter dimension of the footing.ⓘ Width of Footing [B]			+10% -10%

✖Bearing Capacity Factor dependent on Unit Weight is a constant whose value depends upon unit weight of soil.ⓘ Bearing Capacity Factor Dependent on Unit Weight for Strip Footing [N_γ]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Bearing Capacity of Non cohesive Soil Formulas PDF PDF Image

Bearing Capacity Factor Dependent on Unit Weight for Strip Footing Solution

STEP 0: Pre-Calculation Summary

Formula Used

Bearing Capacity Factor dependent on Unit Weight = (Ultimate Bearing Capacity in Soil-(Effective Surcharge in KiloPascal*Bearing Capacity Factor dependent on Surcharge))/(0.5*Unit Weight of Soil*Width of Footing)
N_γ = (q_fc-(σ_s*N_q))/(0.5*γ*B)
This formula uses 6 Variables

Variables Used

Bearing Capacity Factor dependent on Unit Weight - Bearing Capacity Factor dependent on Unit Weight is a constant whose value depends upon unit weight of soil.
Ultimate Bearing Capacity in Soil - (Measured in Pascal) - Ultimate Bearing Capacity in Soil is defined as the minimum gross pressure intensity at the base of the foundation at which the soil fails in shear.
Effective Surcharge in KiloPascal - (Measured in Pascal) - Effective Surcharge in KiloPascal also called as surcharge load refers to the vertical pressure or any load that acts over the ground surface additional to basic earth pressure.
Bearing Capacity Factor dependent on Surcharge - Bearing Capacity Factor dependent on Surcharge is a constant whose value depends upon surcharge.
Unit Weight of Soil - (Measured in Newton per Cubic Meter) - Unit Weight of Soil mass is the ratio of the total weight of soil to the total volume of soil.
Width of Footing - (Measured in Meter) - Width of Footing is the shorter dimension of the footing.

STEP 1: Convert Input(s) to Base Unit

Ultimate Bearing Capacity in Soil: 127.8 Kilopascal --> 127800 Pascal (Check conversion here)
Effective Surcharge in KiloPascal: 45.9 Kilonewton per Square Meter --> 45900 Pascal (Check conversion here)
Bearing Capacity Factor dependent on Surcharge: 2.01 --> No Conversion Required
Unit Weight of Soil: 18 Kilonewton per Cubic Meter --> 18000 Newton per Cubic Meter (Check conversion here)
Width of Footing: 2 Meter --> 2 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

N_γ = (q_fc-(σ_s*N_q))/(0.5*γ*B) --> (127800-(45900*2.01))/(0.5*18000*2)

Evaluating ... ...

N_γ = 1.9745

STEP 3: Convert Result to Output's Unit

1.9745 --> No Conversion Required

FINAL ANSWER

1.9745 <-- Bearing Capacity Factor dependent on Unit Weight

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Civil » Geotechnical Engineering » Bearing Capacity of Non cohesive Soil » Bearing Capacity Factor Dependent on Unit Weight for Strip Footing

Credits

Created by Suraj Kumar

Birsa Institute of Technology (BIT), Sindri

Suraj Kumar has created this Calculator and 2100+ more calculators!

Verified by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has verified this Calculator and 2600+ more calculators!

< Bearing Capacity of Non cohesive Soil Calculators

Bearing Capacity Factor Dependent on Unit Weight for Strip Footing

LaTeX Go Bearing Capacity Factor dependent on Unit Weight = (Ultimate Bearing Capacity in Soil-(Effective Surcharge in KiloPascal*Bearing Capacity Factor dependent on Surcharge))/(0.5*Unit Weight of Soil*Width of Footing)

Effective Surcharge given Bearing Capacity of Non Cohesive Soil for Strip Footing

LaTeX Go Effective Surcharge in KiloPascal = (Ultimate Bearing Capacity in Soil-(0.5*Unit Weight of Soil*Width of Footing*Bearing Capacity Factor dependent on Unit Weight))/Bearing Capacity Factor dependent on Surcharge

Bearing Capacity Factor Dependent on Surcharge for Strip Footing

LaTeX Go Bearing Capacity Factor dependent on Surcharge = (Ultimate Bearing Capacity in Soil-(0.5*Unit Weight of Soil*Width of Footing*Bearing Capacity Factor dependent on Unit Weight))/Effective Surcharge in KiloPascal

Bearing Capacity of Non Cohesive Soil for Strip Footing

LaTeX Go Ultimate Bearing Capacity in Soil = (Effective Surcharge in KiloPascal*Bearing Capacity Factor dependent on Surcharge)+(0.5*Unit Weight of Soil*Width of Footing*Bearing Capacity Factor dependent on Unit Weight)

Bearing Capacity Factor Dependent on Unit Weight for Strip Footing Formula

LaTeX Go

What is Bearing Capacity?

In geotechnical engineering, bearing capacity is the capacity of soil to support the loads applied to the ground. The bearing capacity of soil is the maximum average contact pressure between the foundation and the soil which should not produce shear failure in the soil.

How to Calculate Bearing Capacity Factor Dependent on Unit Weight for Strip Footing?

Bearing Capacity Factor Dependent on Unit Weight for Strip Footing calculator uses Bearing Capacity Factor dependent on Unit Weight = (Ultimate Bearing Capacity in Soil-(Effective Surcharge in KiloPascal*Bearing Capacity Factor dependent on Surcharge))/(0.5*Unit Weight of Soil*Width of Footing) to calculate the Bearing Capacity Factor dependent on Unit Weight, The Bearing Capacity Factor Dependent on Unit Weight for Strip Footing is defined as the value of bearing capacity factor dependent on the unit weight when we have prior information of other parameters used. Bearing Capacity Factor dependent on Unit Weight is denoted by N_γ symbol.

How to calculate Bearing Capacity Factor Dependent on Unit Weight for Strip Footing using this online calculator? To use this online calculator for Bearing Capacity Factor Dependent on Unit Weight for Strip Footing, enter Ultimate Bearing Capacity in Soil (q_fc), Effective Surcharge in KiloPascal (σ_s), Bearing Capacity Factor dependent on Surcharge (N_q), Unit Weight of Soil (γ) & Width of Footing (B) and hit the calculate button. Here is how the Bearing Capacity Factor Dependent on Unit Weight for Strip Footing calculation can be explained with given input values -> 2 = (127800-(45900*2.01))/(0.5*18000*2).

FAQ

What is Bearing Capacity Factor Dependent on Unit Weight for Strip Footing?

The Bearing Capacity Factor Dependent on Unit Weight for Strip Footing is defined as the value of bearing capacity factor dependent on the unit weight when we have prior information of other parameters used and is represented as N_γ = (q_fc-(σ_s*N_q))/(0.5*γ*B) or Bearing Capacity Factor dependent on Unit Weight = (Ultimate Bearing Capacity in Soil-(Effective Surcharge in KiloPascal*Bearing Capacity Factor dependent on Surcharge))/(0.5*Unit Weight of Soil*Width of Footing). Ultimate Bearing Capacity in Soil is defined as the minimum gross pressure intensity at the base of the foundation at which the soil fails in shear, Effective Surcharge in KiloPascal also called as surcharge load refers to the vertical pressure or any load that acts over the ground surface additional to basic earth pressure, Bearing Capacity Factor dependent on Surcharge is a constant whose value depends upon surcharge, Unit Weight of Soil mass is the ratio of the total weight of soil to the total volume of soil & Width of Footing is the shorter dimension of the footing.

How to calculate Bearing Capacity Factor Dependent on Unit Weight for Strip Footing?

The Bearing Capacity Factor Dependent on Unit Weight for Strip Footing is defined as the value of bearing capacity factor dependent on the unit weight when we have prior information of other parameters used is calculated using Bearing Capacity Factor dependent on Unit Weight = (Ultimate Bearing Capacity in Soil-(Effective Surcharge in KiloPascal*Bearing Capacity Factor dependent on Surcharge))/(0.5*Unit Weight of Soil*Width of Footing). To calculate Bearing Capacity Factor Dependent on Unit Weight for Strip Footing, you need Ultimate Bearing Capacity in Soil (q_fc), Effective Surcharge in KiloPascal (σ_s), Bearing Capacity Factor dependent on Surcharge (N_q), Unit Weight of Soil (γ) & Width of Footing (B). With our tool, you need to enter the respective value for Ultimate Bearing Capacity in Soil, Effective Surcharge in KiloPascal, Bearing Capacity Factor dependent on Surcharge, Unit Weight of Soil & Width of Footing and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Bearing Capacity Factor dependent on Unit Weight?

In this formula, Bearing Capacity Factor dependent on Unit Weight uses Ultimate Bearing Capacity in Soil, Effective Surcharge in KiloPascal, Bearing Capacity Factor dependent on Surcharge, Unit Weight of Soil & Width of Footing. We can use 2 other way(s) to calculate the same, which is/are as follows -

Bearing Capacity Factor dependent on Unit Weight = (Ultimate Bearing Capacity in Soil-(Effective Surcharge in KiloPascal*Bearing Capacity Factor dependent on Surcharge))/(0.3*Unit Weight of Soil*Diameter of Section)
Bearing Capacity Factor dependent on Unit Weight = (Ultimate Bearing Capacity in Soil-(Effective Surcharge in KiloPascal*Bearing Capacity Factor dependent on Surcharge))/(0.4*Unit Weight of Soil*Width of Footing)

Home

FREE PDFs

🔍 Search