Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction Calculator

✖Bearing Capacity Factor dependent on Surcharge is a constant whose value depends upon surcharge.ⓘ Bearing Capacity Factor dependent on Surcharge [N_q]			+10% -10%
✖Angle of Internal Friction is the angle measured between the normal force and resultant force .ⓘ Angle of Internal Friction [φ]			+10% -10%

✖Bearing Capacity Factor dependent on Unit Weight is a constant whose value depends upon unit weight of soil.ⓘ Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction [N_γ]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Geotechnical Engineering Formula PDF PDF Image

Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction Solution

STEP 0: Pre-Calculation Summary

Formula Used

Bearing Capacity Factor dependent on Unit Weight = (Bearing Capacity Factor dependent on Surcharge-1)*tan(1.4*(Angle of Internal Friction))
N_γ = (N_q-1)*tan(1.4*(φ))
This formula uses 1 Functions, 3 Variables

Functions Used

tan - The tangent of an angle is a trigonometric ratio of the length of the side opposite an angle to the length of the side adjacent to an angle in a right triangle., tan(Angle)

Variables Used

Bearing Capacity Factor dependent on Unit Weight - Bearing Capacity Factor dependent on Unit Weight is a constant whose value depends upon unit weight of soil.
Bearing Capacity Factor dependent on Surcharge - Bearing Capacity Factor dependent on Surcharge is a constant whose value depends upon surcharge.
Angle of Internal Friction - (Measured in Radian) - Angle of Internal Friction is the angle measured between the normal force and resultant force .

STEP 1: Convert Input(s) to Base Unit

Bearing Capacity Factor dependent on Surcharge: 2.01 --> No Conversion Required
Angle of Internal Friction: 46 Degree --> 0.802851455917241 Radian (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

N_γ = (N_q-1)*tan(1.4*(φ)) --> (2.01-1)*tan(1.4*(0.802851455917241))

Evaluating ... ...

N_γ = 2.10803261666031

STEP 3: Convert Result to Output's Unit

2.10803261666031 --> No Conversion Required

FINAL ANSWER

2.10803261666031 ≈ 2.108033 <-- Bearing Capacity Factor dependent on Unit Weight

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Civil » Geotechnical Engineering » Bearing Capacity of Soils by Meyerhof's Analysis » Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction

Credits

Created by Suraj Kumar

Birsa Institute of Technology (BIT), Sindri

Suraj Kumar has created this Calculator and 2100+ more calculators!

Verified by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has verified this Calculator and 2600+ more calculators!

< Bearing Capacity of Soils by Meyerhof's Analysis Calculators

Length of Footing given Angle of Shearing Resistance by Meyerhof's Analysis

LaTeX Go Length of Footing = (0.1*Width of Footing)/(1.1-(Angle of Internal Friction For Plain Strain/Angle of Internal Friction))

Width of Footing given Angle of Shearing Resistance by Meyerhof's Analysis

LaTeX Go Width of Footing = (1.1-(Angle of Internal Friction For Plain Strain/Angle of Internal Friction))*(Length of Footing/0.1)

Plane Strain Angle of Shearing Resistance by Meyerhof's Analysis

LaTeX Go Angle of Internal Friction For Plain Strain = (1.1-0.1*(Width of Footing/Length of Footing))*Angle of Internal Friction

Triaxial Angle of Shearing Resistance by Meyerhof's Analysis

LaTeX Go Angle of Internal Friction = Angle of Internal Friction For Plain Strain/(1.1-0.1*(Width of Footing/Length of Footing))

Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction Formula

LaTeX Go

Bearing Capacity Factor dependent on Unit Weight = (Bearing Capacity Factor dependent on Surcharge-1)*tan(1.4*(Angle of Internal Friction))
N_γ = (N_q-1)*tan(1.4*(φ))

What is Bearing Capacity?

In geotechnical engineering, bearing capacity is the capacity of soil to support the loads applied to the ground. The bearing capacity of soil is the maximum average contact pressure between the foundation and the soil which should not produce shear failure in the soil.

what are bearing capacity factors?

Bearing capacity factors are empirically derived factors used in a bearing capacity equation that usually correlates with the angle of internal friction of the soil.

How to Calculate Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction?

Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction calculator uses Bearing Capacity Factor dependent on Unit Weight = (Bearing Capacity Factor dependent on Surcharge-1)*tan(1.4*(Angle of Internal Friction)) to calculate the Bearing Capacity Factor dependent on Unit Weight, The Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction is defined as the value of bearing capacity factor dependent on unit weight when we have prior information of other parameters used. Bearing Capacity Factor dependent on Unit Weight is denoted by N_γ symbol.

How to calculate Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction using this online calculator? To use this online calculator for Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction, enter Bearing Capacity Factor dependent on Surcharge (N_q) & Angle of Internal Friction (φ) and hit the calculate button. Here is how the Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction calculation can be explained with given input values -> 2.087161 = (2.01-1)*tan(1.4*(0.802851455917241)).

FAQ

What is Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction?

The Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction is defined as the value of bearing capacity factor dependent on unit weight when we have prior information of other parameters used and is represented as N_γ = (N_q-1)*tan(1.4*(φ)) or Bearing Capacity Factor dependent on Unit Weight = (Bearing Capacity Factor dependent on Surcharge-1)*tan(1.4*(Angle of Internal Friction)). Bearing Capacity Factor dependent on Surcharge is a constant whose value depends upon surcharge & Angle of Internal Friction is the angle measured between the normal force and resultant force .

How to calculate Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction?

The Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction is defined as the value of bearing capacity factor dependent on unit weight when we have prior information of other parameters used is calculated using Bearing Capacity Factor dependent on Unit Weight = (Bearing Capacity Factor dependent on Surcharge-1)*tan(1.4*(Angle of Internal Friction)). To calculate Bearing Capacity Factor Dependent on Unit Weight Given Angle of Internal Friction, you need Bearing Capacity Factor dependent on Surcharge (N_q) & Angle of Internal Friction (φ). With our tool, you need to enter the respective value for Bearing Capacity Factor dependent on Surcharge & Angle of Internal Friction and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search