Average Output Power of Three Phase Half Wave Diode Rectifier with R Load Calculator

✖Peak Phase Voltage is the maximum amplitude of the phase voltage of a 3 phase system.ⓘ Peak Phase Voltage [V_m(phase)]			+10% -10%
✖Peak Phase Current is the maximum amplitude of the current acquired by any phase of a 3 phase system.ⓘ Peak Phase Current [I_m(phase)]			+10% -10%

✖Average Output Power refers to the mean power delivered by an electrical or electronic device over a specific period.ⓘ Average Output Power of Three Phase Half Wave Diode Rectifier with R Load [P_avg]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Three Phase Uncontrolled Rectifiers Formulas PDF PDF Image

Average Output Power of Three Phase Half Wave Diode Rectifier with R Load Solution

STEP 0: Pre-Calculation Summary

Formula Used

Average Output Power = 0.684*Peak Phase Voltage*Peak Phase Current
P_avg = 0.684*V_m(phase)*I_m(phase)
This formula uses 3 Variables

Variables Used

Average Output Power - (Measured in Watt) - Average Output Power refers to the mean power delivered by an electrical or electronic device over a specific period.
Peak Phase Voltage - (Measured in Volt) - Peak Phase Voltage is the maximum amplitude of the phase voltage of a 3 phase system.
Peak Phase Current - (Measured in Ampere) - Peak Phase Current is the maximum amplitude of the current acquired by any phase of a 3 phase system.

STEP 1: Convert Input(s) to Base Unit

Peak Phase Voltage: 115.1 Volt --> 115.1 Volt No Conversion Required
Peak Phase Current: 4.105 Ampere --> 4.105 Ampere No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

P_avg = 0.684*V_m(phase)*I_m(phase) --> 0.684*115.1*4.105

Evaluating ... ...

P_avg = 323.180082

STEP 3: Convert Result to Output's Unit

323.180082 Watt --> No Conversion Required

FINAL ANSWER

323.180082 ≈ 323.1801 Watt <-- Average Output Power

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power Electronics » Uncontrolled Rectifiers » Three Phase Uncontrolled Rectifiers » Half Wave » Average Output Power of Three Phase Half Wave Diode Rectifier with R Load

Credits

Created by Pratik Kumar Singh

Vellore Institute of Technology (VIT), Vellore

Pratik Kumar Singh has created this Calculator and 10+ more calculators!

Verified by Parminder Singh

Chandigarh University (CU), Punjab

Parminder Singh has verified this Calculator and 500+ more calculators!

< Half Wave Calculators

Average Output Voltage of Three Phase Half Wave Diode Rectifier with R Load in Phase Voltage Terms

LaTeX Go Average Output Voltage = ((3*sqrt(3))/(2*pi))*Peak Phase Voltage

Average Output Voltage of Three Phase Half Wave Diode Rectifier with R Load in Line Voltage Terms

LaTeX Go Average Output Voltage = (3/(2*pi))*Peak Line Voltage

RMS Output Current of Three Phase Half Wave Diode Rectifier with R Load

LaTeX Go Root Mean Square Current = 0.4854*Peak Phase Current

RMS Output Voltage of Three Phase Half Wave Diode Rectifier with Resistive Load

LaTeX Go RMS Output Voltage = 0.84068*Peak Phase Voltage

Average Output Power of Three Phase Half Wave Diode Rectifier with R Load Formula

LaTeX Go

Average Output Power = 0.684*Peak Phase Voltage*Peak Phase Current
P_avg = 0.684*V_m(phase)*I_m(phase)

How does the ripple in the output voltage affect the average output power?

The ripple in the output voltage of a three-phase half-wave diode rectifier has a direct impact on the average output power. This ripple represents variations in the rectified DC voltage, causing fluctuations above and below the desired average DC level. When the ripple is high, it reduces the overall average voltage, leading to a decrease in average output power.

How to Calculate Average Output Power of Three Phase Half Wave Diode Rectifier with R Load?

Average Output Power of Three Phase Half Wave Diode Rectifier with R Load calculator uses Average Output Power = 0.684*Peak Phase Voltage*Peak Phase Current to calculate the Average Output Power, The Average Output Power of Three Phase Half Wave Diode Rectifier with R Load formula is defined as is the average electrical power delivered to the load over a full cycle of operation. A Three-Phase Half-Wave Diode Rectifier is used to convert three-phase alternating current (AC) into direct current (DC). Average Output Power is denoted by P_avg symbol.

How to calculate Average Output Power of Three Phase Half Wave Diode Rectifier with R Load using this online calculator? To use this online calculator for Average Output Power of Three Phase Half Wave Diode Rectifier with R Load, enter Peak Phase Voltage (V_m(phase)) & Peak Phase Current (I_m(phase)) and hit the calculate button. Here is how the Average Output Power of Three Phase Half Wave Diode Rectifier with R Load calculation can be explained with given input values -> 323.1801 = 0.684*115.1*4.105.

FAQ

What is Average Output Power of Three Phase Half Wave Diode Rectifier with R Load?

The Average Output Power of Three Phase Half Wave Diode Rectifier with R Load formula is defined as is the average electrical power delivered to the load over a full cycle of operation. A Three-Phase Half-Wave Diode Rectifier is used to convert three-phase alternating current (AC) into direct current (DC) and is represented as P_avg = 0.684*V_m(phase)*I_m(phase) or Average Output Power = 0.684*Peak Phase Voltage*Peak Phase Current. Peak Phase Voltage is the maximum amplitude of the phase voltage of a 3 phase system & Peak Phase Current is the maximum amplitude of the current acquired by any phase of a 3 phase system.

How to calculate Average Output Power of Three Phase Half Wave Diode Rectifier with R Load?

The Average Output Power of Three Phase Half Wave Diode Rectifier with R Load formula is defined as is the average electrical power delivered to the load over a full cycle of operation. A Three-Phase Half-Wave Diode Rectifier is used to convert three-phase alternating current (AC) into direct current (DC) is calculated using Average Output Power = 0.684*Peak Phase Voltage*Peak Phase Current. To calculate Average Output Power of Three Phase Half Wave Diode Rectifier with R Load, you need Peak Phase Voltage (V_m(phase)) & Peak Phase Current (I_m(phase)). With our tool, you need to enter the respective value for Peak Phase Voltage & Peak Phase Current and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search