Area of X-Section (DC Two-Wire US) Calculator

✖Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work.ⓘ Power Transmitted [P]			+10% -10%
✖Resistivity is the measure of how strongly a material opposes the flow of current through them.ⓘ Resistivity [ρ]			+10% -10%
✖Length of Wire DC is the measurement or extent of something from end to end.ⓘ Length of Wire DC [l]			+10% -10%
✖Line Losses is defined as the losses that are produced in the line.ⓘ Line Losses [P_line]			+10% -10%
✖Maximum Voltage the highest voltage rating for electrical devices.ⓘ Maximum Voltage [V_m]			+10% -10%

✖The Area of underground dc wire is the amount of two-dimensional space taken up by an object.ⓘ Area of X-Section (DC Two-Wire US) [A]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Power System Formula PDF PDF Image

Area of X-Section (DC Two-Wire US) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Area of underground dc wire = 2*(Power Transmitted^2)*Resistivity*Length of Wire DC/(Line Losses*(Maximum Voltage^2))
A = 2*(P^2)*ρ*l/(P_line*(V_m^2))
This formula uses 6 Variables

Variables Used

Area of underground dc wire - (Measured in Square Meter) - The Area of underground dc wire is the amount of two-dimensional space taken up by an object.
Power Transmitted - (Measured in Watt) - Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work.
Resistivity - (Measured in Ohm Meter) - Resistivity is the measure of how strongly a material opposes the flow of current through them.
Length of Wire DC - (Measured in Meter) - Length of Wire DC is the measurement or extent of something from end to end.
Line Losses - (Measured in Watt) - Line Losses is defined as the losses that are produced in the line.
Maximum Voltage - (Measured in Volt) - Maximum Voltage the highest voltage rating for electrical devices.

STEP 1: Convert Input(s) to Base Unit

Power Transmitted: 300 Watt --> 300 Watt No Conversion Required
Resistivity: 1.7E-05 Ohm Meter --> 1.7E-05 Ohm Meter No Conversion Required
Length of Wire DC: 3.2 Meter --> 3.2 Meter No Conversion Required
Line Losses: 0.6 Watt --> 0.6 Watt No Conversion Required
Maximum Voltage: 60 Volt --> 60 Volt No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

A = 2*(P^2)*ρ*l/(P_line*(V_m^2)) --> 2*(300^2)*1.7E-05*3.2/(0.6*(60^2))

Evaluating ... ...

A = 0.00453333333333333

STEP 3: Convert Result to Output's Unit

0.00453333333333333 Square Meter --> No Conversion Required

FINAL ANSWER

0.00453333333333333 ≈ 0.004533 Square Meter <-- Area of underground dc wire

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Electrical » Power System » Underground DC Supply » 2 Wire System » Wire Parameters » Area of X-Section (DC Two-Wire US)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< Wire Parameters Calculators

Volume of Conductor Material using Resistance (DC Two-Wire US)

LaTeX Go Volume Of Conductor = (4*(Power Transmitted^2)*Resistance underground DC*Area of underground dc wire*Length of Wire DC)/(Line Losses*(Maximum Voltage^2))

Volume of Conductor Material (DC Two-Wire US)

LaTeX Go Volume Of Conductor = 4*(Power Transmitted^2)*Resistivity*(Length of Wire DC^2)/(Line Losses*(Maximum Voltage^2))

Volume of Conductor Material using Load Current (DC Two-Wire US)

LaTeX Go Volume Of Conductor = 4*Resistivity*(Length of Wire DC^2)*(Current underground DC^2)/Line Losses

Volume of Conductor Material using Area and Length(DC Two-Wire US)

LaTeX Go Volume Of Conductor = Area of underground dc wire*Length of Wire DC*2

Area of X-Section (DC Two-Wire US) Formula

LaTeX Go

Area of underground dc wire = 2*(Power Transmitted^2)*Resistivity*Length of Wire DC/(Line Losses*(Maximum Voltage^2))
A = 2*(P^2)*ρ*l/(P_line*(V_m^2))

What is the volume of conductor material in DC Two-Wire underground system?

The volume of conductor material required in this system is 1 times that of a 2-wire d.c.system with the one conductor earthed.

How to Calculate Area of X-Section (DC Two-Wire US)?

Area of X-Section (DC Two-Wire US) calculator uses Area of underground dc wire = 2*(Power Transmitted^2)*Resistivity*Length of Wire DC/(Line Losses*(Maximum Voltage^2)) to calculate the Area of underground dc wire, Area of X-Section (DC Two-Wire US) formula is defined as the cross-sectional area simply as the square of the wire's diameter in mils and calls that our area in units of “circular mils.” This makes number handling ever so much easier. Area of underground dc wire is denoted by A symbol.

How to calculate Area of X-Section (DC Two-Wire US) using this online calculator? To use this online calculator for Area of X-Section (DC Two-Wire US), enter Power Transmitted (P), Resistivity (ρ), Length of Wire DC (l), Line Losses (P_line) & Maximum Voltage (V_m) and hit the calculate button. Here is how the Area of X-Section (DC Two-Wire US) calculation can be explained with given input values -> 0.004533 = 2*(300^2)*1.7E-05*3.2/(0.6*(60^2)).

FAQ

What is Area of X-Section (DC Two-Wire US)?

Area of X-Section (DC Two-Wire US) formula is defined as the cross-sectional area simply as the square of the wire's diameter in mils and calls that our area in units of “circular mils.” This makes number handling ever so much easier and is represented as A = 2*(P^2)*ρ*l/(P_line*(V_m^2)) or Area of underground dc wire = 2*(Power Transmitted^2)*Resistivity*Length of Wire DC/(Line Losses*(Maximum Voltage^2)). Power Transmitted is the amount of power that is transferred from its place of generation to a location where it is applied to perform useful work, Resistivity is the measure of how strongly a material opposes the flow of current through them, Length of Wire DC is the measurement or extent of something from end to end, Line Losses is defined as the losses that are produced in the line & Maximum Voltage the highest voltage rating for electrical devices.

How to calculate Area of X-Section (DC Two-Wire US)?

Area of X-Section (DC Two-Wire US) formula is defined as the cross-sectional area simply as the square of the wire's diameter in mils and calls that our area in units of “circular mils.” This makes number handling ever so much easier is calculated using Area of underground dc wire = 2*(Power Transmitted^2)*Resistivity*Length of Wire DC/(Line Losses*(Maximum Voltage^2)). To calculate Area of X-Section (DC Two-Wire US), you need Power Transmitted (P), Resistivity (ρ), Length of Wire DC (l), Line Losses (P_line) & Maximum Voltage (V_m). With our tool, you need to enter the respective value for Power Transmitted, Resistivity, Length of Wire DC, Line Losses & Maximum Voltage and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search