Adjusted Design Value for Withdrawal for Nails and Spikes Calculator

✖Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures.ⓘ Nominal Design Value for Withdrawal [W]			+10% -10%
✖Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time.ⓘ Load Duration Factor [C_D]			+10% -10%
✖Wet Service Factor is used to signify wood that will not be used in a dry condition.ⓘ Wet Service Factor [C_m]			+10% -10%
✖Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.ⓘ Temperature Factor [C_t]			+10% -10%
✖Toenail Factor is the adjustment factor used for wood design.ⓘ Toenail Factor [C_tn]			+10% -10%

✖Adjusted design value for withdrawal is given in terms of nominal design values and adjustment factors.ⓘ Adjusted Design Value for Withdrawal for Nails and Spikes [W']

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Timber Engineering Formula PDF PDF Image

Adjusted Design Value for Withdrawal for Nails and Spikes Solution

STEP 0: Pre-Calculation Summary

Formula Used

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor
W' = W*C_D*C_m*C_t*C_tn
This formula uses 6 Variables

Variables Used

Adjusted Design Value for Withdrawal - (Measured in Newton) - Adjusted design value for withdrawal is given in terms of nominal design values and adjustment factors.
Nominal Design Value for Withdrawal - (Measured in Newton) - Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures.
Load Duration Factor - Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time.
Wet Service Factor - Wet Service Factor is used to signify wood that will not be used in a dry condition.
Temperature Factor - Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.
Toenail Factor - Toenail Factor is the adjustment factor used for wood design.

STEP 1: Convert Input(s) to Base Unit

Nominal Design Value for Withdrawal: 50 Newton --> 50 Newton No Conversion Required
Load Duration Factor: 0.74 --> No Conversion Required
Wet Service Factor: 0.81 --> No Conversion Required
Temperature Factor: 0.8 --> No Conversion Required
Toenail Factor: 0.83 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

W' = W*C_D*C_m*C_t*C_tn --> 50*0.74*0.81*0.8*0.83

Evaluating ... ...

W' = 19.90008

STEP 3: Convert Result to Output's Unit

19.90008 Newton --> No Conversion Required

FINAL ANSWER

19.90008 Newton <-- Adjusted Design Value for Withdrawal

(Calculation completed in 00.021 seconds)

You are here -

Home » Engineering » Civil » Timber Engineering » Adjustment of Design Values for Connections with Fasteners » Adjusted Design Value for Withdrawal for Nails and Spikes

Credits

Created by Chandana P Dev

NSS College of Engineering (NSSCE), Palakkad

Chandana P Dev has created this Calculator and 500+ more calculators!

Verified by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has verified this Calculator and 700+ more calculators!

< Adjustment of Design Values for Connections with Fasteners Calculators

Adjusted Value for Loading Parallel to Grain for Split Ring and Shear Plate Connectors

LaTeX Go Adjusted Value for Loading Perpendicular to Grain = Nominal Design Value for Loading Parallel to Grain*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor*Penetration Depth Factor*Metal Side-Plate Factor

Adjusted Value for Loading Normal to Grain for Split Ring and Shear Plate Connectors

LaTeX Go Adjusted Value for Loading Normal to Grain = Nominal Design Value for Loading Normal to Grain*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor*Penetration Depth Factor

Adjusted Design Value for Lateral Loading for Bolts

LaTeX Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor

Adjusted Design Value for Withdrawal for Nails and Spikes

LaTeX Go Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor

Adjusted Design Value for Withdrawal for Nails and Spikes Formula

LaTeX Go

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor
W' = W*C_D*C_m*C_t*C_tn

What is Adjusted Design Value for Withdrawal?

Nominal design values for laterally loaded fasteners Z, withdrawal of fasteners W, load parallel to grain P, and load perpendicular to grain Q should be multiplied by applicable adjustment factors to determine adjusted design values. The load applied to a connection should not exceed the adjusted design value.

What are Nails and Spikes?

In wood-working and construction, a nail is a small object made of metal (or wood, called a tree nail) which is used as a fastener.

How to Calculate Adjusted Design Value for Withdrawal for Nails and Spikes?

Adjusted Design Value for Withdrawal for Nails and Spikes calculator uses Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor to calculate the Adjusted Design Value for Withdrawal, Adjusted Design Value for Withdrawal for Nails and Spikes is defined as the value which is the product of nominal design value for withdrawal load and adjustment factors for nails and spikes. Adjusted Design Value for Withdrawal is denoted by W' symbol.

How to calculate Adjusted Design Value for Withdrawal for Nails and Spikes using this online calculator? To use this online calculator for Adjusted Design Value for Withdrawal for Nails and Spikes, enter Nominal Design Value for Withdrawal (W), Load Duration Factor (C_D), Wet Service Factor (C_m), Temperature Factor (C_t) & Toenail Factor (C_tn) and hit the calculate button. Here is how the Adjusted Design Value for Withdrawal for Nails and Spikes calculation can be explained with given input values -> 19.90008 = 50*0.74*0.81*0.8*0.83.

FAQ

What is Adjusted Design Value for Withdrawal for Nails and Spikes?

Adjusted Design Value for Withdrawal for Nails and Spikes is defined as the value which is the product of nominal design value for withdrawal load and adjustment factors for nails and spikes and is represented as W' = W*C_D*C_m*C_t*C_tn or Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor. Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures, Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time, Wet Service Factor is used to signify wood that will not be used in a dry condition, Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time & Toenail Factor is the adjustment factor used for wood design.

How to calculate Adjusted Design Value for Withdrawal for Nails and Spikes?

Adjusted Design Value for Withdrawal for Nails and Spikes is defined as the value which is the product of nominal design value for withdrawal load and adjustment factors for nails and spikes is calculated using Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor. To calculate Adjusted Design Value for Withdrawal for Nails and Spikes, you need Nominal Design Value for Withdrawal (W), Load Duration Factor (C_D), Wet Service Factor (C_m), Temperature Factor (C_t) & Toenail Factor (C_tn). With our tool, you need to enter the respective value for Nominal Design Value for Withdrawal, Load Duration Factor, Wet Service Factor, Temperature Factor & Toenail Factor and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Adjusted Design Value for Withdrawal?

In this formula, Adjusted Design Value for Withdrawal uses Nominal Design Value for Withdrawal, Load Duration Factor, Wet Service Factor, Temperature Factor & Toenail Factor. We can use 3 other way(s) to calculate the same, which is/are as follows -

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor
Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*End Grain Factor*Temperature Factor
Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*End Grain Factor

Home

FREE PDFs

🔍 Search