Adjusted Design Value for Withdrawal for Lag Screws Calculator

✖Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures.ⓘ Nominal Design Value for Withdrawal [W]			+10% -10%
✖Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time.ⓘ Load Duration Factor [C_D]			+10% -10%
✖Wet Service Factor is used to signify wood that will not be used in a dry condition.ⓘ Wet Service Factor [C_m]			+10% -10%
✖End Grain Factor is a factor used for wood design. End grain is the grain of wood seen when it is cut across the growth rings.ⓘ End Grain Factor [C_eg]			+10% -10%
✖Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.ⓘ Temperature Factor [C_t]			+10% -10%

✖Adjusted design value for withdrawal is given in terms of nominal design values and adjustment factors.ⓘ Adjusted Design Value for Withdrawal for Lag Screws [W']

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Timber Engineering Formula PDF PDF Image

Adjusted Design Value for Withdrawal for Lag Screws Solution

STEP 0: Pre-Calculation Summary

Formula Used

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*End Grain Factor*Temperature Factor
W' = W*C_D*C_m*C_eg*C_t
This formula uses 6 Variables

Variables Used

Adjusted Design Value for Withdrawal - (Measured in Newton) - Adjusted design value for withdrawal is given in terms of nominal design values and adjustment factors.
Nominal Design Value for Withdrawal - (Measured in Newton) - Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures.
Load Duration Factor - Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time.
Wet Service Factor - Wet Service Factor is used to signify wood that will not be used in a dry condition.
End Grain Factor - End Grain Factor is a factor used for wood design. End grain is the grain of wood seen when it is cut across the growth rings.
Temperature Factor - Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.

STEP 1: Convert Input(s) to Base Unit

Nominal Design Value for Withdrawal: 50 Newton --> 50 Newton No Conversion Required
Load Duration Factor: 0.74 --> No Conversion Required
Wet Service Factor: 0.81 --> No Conversion Required
End Grain Factor: 0.75 --> No Conversion Required
Temperature Factor: 0.8 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

W' = W*C_D*C_m*C_eg*C_t --> 50*0.74*0.81*0.75*0.8

Evaluating ... ...

W' = 17.982

STEP 3: Convert Result to Output's Unit

17.982 Newton --> No Conversion Required

FINAL ANSWER

17.982 Newton <-- Adjusted Design Value for Withdrawal

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Timber Engineering » Adjustment of Design Values for Connections with Fasteners » Adjusted Design Value for Withdrawal for Lag Screws

Credits

Created by Chandana P Dev

NSS College of Engineering (NSSCE), Palakkad

Chandana P Dev has created this Calculator and 500+ more calculators!

Verified by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has verified this Calculator and 2600+ more calculators!

< Adjustment of Design Values for Connections with Fasteners Calculators

Adjusted Value for Loading Parallel to Grain for Split Ring and Shear Plate Connectors

LaTeX Go Adjusted Value for Loading Perpendicular to Grain = Nominal Design Value for Loading Parallel to Grain*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor*Penetration Depth Factor*Metal Side-Plate Factor

Adjusted Value for Loading Normal to Grain for Split Ring and Shear Plate Connectors

LaTeX Go Adjusted Value for Loading Normal to Grain = Nominal Design Value for Loading Normal to Grain*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor*Penetration Depth Factor

Adjusted Design Value for Lateral Loading for Bolts

LaTeX Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor

Adjusted Design Value for Withdrawal for Nails and Spikes

LaTeX Go Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor

Adjusted Design Value for Withdrawal for Lag Screws Formula

LaTeX Go

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*End Grain Factor*Temperature Factor
W' = W*C_D*C_m*C_eg*C_t

What is Adjusted Design Value for Withdrawal?

Nominal design values for laterally loaded fasteners Z, withdrawal of fasteners W, load parallel to grain P, and load perpendicular to grain Q should be multiplied by applicable adjustment factors to determine adjusted design values. The load applied to a connection should not exceed the adjusted design value.

What are the Adjustment Factors used for Lag Screw Withdrawal Value?

Load duration factor, wet service factor, end grain factor and temperature factor. Withdrawal loading is always applied in the direction parallel to length of fastener.

How to Calculate Adjusted Design Value for Withdrawal for Lag Screws?

Adjusted Design Value for Withdrawal for Lag Screws calculator uses Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*End Grain Factor*Temperature Factor to calculate the Adjusted Design Value for Withdrawal, The Adjusted Design Value for Withdrawal for Lag Screws formula is defined as the nominal design value multiplied by the adjustment factors. Adjusted Design Value for Withdrawal is denoted by W' symbol.

How to calculate Adjusted Design Value for Withdrawal for Lag Screws using this online calculator? To use this online calculator for Adjusted Design Value for Withdrawal for Lag Screws, enter Nominal Design Value for Withdrawal (W), Load Duration Factor (C_D), Wet Service Factor (C_m), End Grain Factor (C_eg) & Temperature Factor (C_t) and hit the calculate button. Here is how the Adjusted Design Value for Withdrawal for Lag Screws calculation can be explained with given input values -> 17.982 = 50*0.74*0.81*0.75*0.8.

FAQ

What is Adjusted Design Value for Withdrawal for Lag Screws?

The Adjusted Design Value for Withdrawal for Lag Screws formula is defined as the nominal design value multiplied by the adjustment factors and is represented as W' = W*C_D*C_m*C_eg*C_t or Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*End Grain Factor*Temperature Factor. Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures, Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time, Wet Service Factor is used to signify wood that will not be used in a dry condition, End Grain Factor is a factor used for wood design. End grain is the grain of wood seen when it is cut across the growth rings & Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.

How to calculate Adjusted Design Value for Withdrawal for Lag Screws?

The Adjusted Design Value for Withdrawal for Lag Screws formula is defined as the nominal design value multiplied by the adjustment factors is calculated using Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*End Grain Factor*Temperature Factor. To calculate Adjusted Design Value for Withdrawal for Lag Screws, you need Nominal Design Value for Withdrawal (W), Load Duration Factor (C_D), Wet Service Factor (C_m), End Grain Factor (C_eg) & Temperature Factor (C_t). With our tool, you need to enter the respective value for Nominal Design Value for Withdrawal, Load Duration Factor, Wet Service Factor, End Grain Factor & Temperature Factor and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Adjusted Design Value for Withdrawal?

In this formula, Adjusted Design Value for Withdrawal uses Nominal Design Value for Withdrawal, Load Duration Factor, Wet Service Factor, End Grain Factor & Temperature Factor. We can use 3 other way(s) to calculate the same, which is/are as follows -

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor
Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor
Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*End Grain Factor

Home

FREE PDFs

🔍 Search