Adjusted Design Value for Compression Perpendicular to Grain Calculator

✖Design Value for Compression Perpendicular corrects the design value by using some factor.ⓘ Design Value for Compression Perpendicular [F_c⊥]			+10% -10%
✖Wet Service Factor is used to signify wood that will not be used in a dry condition.ⓘ Wet Service Factor [C_m]			+10% -10%
✖Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.ⓘ Temperature Factor [C_t]			+10% -10%
✖Bearing area factor is used to increase design values for concentrated loads on wood perpendicular to the grain.ⓘ Bearing Area Factor [C_b]			+10% -10%

✖Adjusted design value is the value either in bending, compression, tension or shear by using other factors.ⓘ Adjusted Design Value for Compression Perpendicular to Grain [F']

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download Adjustment Factors for Design Values Formulas PDF PDF Image

Adjusted Design Value for Compression Perpendicular to Grain Solution

STEP 0: Pre-Calculation Summary

Formula Used

Adjusted Design Value = Design Value for Compression Perpendicular*Wet Service Factor*Temperature Factor*Bearing Area Factor
F' = F_c⊥*C_m*C_t*C_b
This formula uses 5 Variables

Variables Used

Adjusted Design Value - (Measured in Pascal) - Adjusted design value is the value either in bending, compression, tension or shear by using other factors.
Design Value for Compression Perpendicular - (Measured in Pascal) - Design Value for Compression Perpendicular corrects the design value by using some factor.
Wet Service Factor - Wet Service Factor is used to signify wood that will not be used in a dry condition.
Temperature Factor - Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.
Bearing Area Factor - Bearing area factor is used to increase design values for concentrated loads on wood perpendicular to the grain.

STEP 1: Convert Input(s) to Base Unit

Design Value for Compression Perpendicular: 9 Megapascal --> 9000000 Pascal (Check conversion here)
Wet Service Factor: 0.81 --> No Conversion Required
Temperature Factor: 0.8 --> No Conversion Required
Bearing Area Factor: 1.0075 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

F' = F_c⊥*C_m*C_t*C_b --> 9000000*0.81*0.8*1.0075

Evaluating ... ...

F' = 5875740

STEP 3: Convert Result to Output's Unit

5875740 Pascal -->5.87574 Megapascal (Check conversion here)

FINAL ANSWER

5.87574 Megapascal <-- Adjusted Design Value

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Timber Engineering » Adjustment Factors for Design Values » Adjusted Design Value for Compression Perpendicular to Grain

Credits

Created by Suraj Kumar

Birsa Institute of Technology (BIT), Sindri

Suraj Kumar has created this Calculator and 2100+ more calculators!

Verified by Himanshi Sharma

Bhilai Institute of Technology (BIT), Raipur

Himanshi Sharma has verified this Calculator and 800+ more calculators!

< Adjustment Factors for Design Values Calculators

Adjusted Design Value for Compression Parallel to Grain

LaTeX Go Adjusted Design Value = (Design Value for Parallel Compression*Load Duration Factor*Wet Service Factor*Temperature Factor*Size Factor*Column Stability Factor)

Adjusted Design Value for Shear

LaTeX Go Adjusted Design Value = Design Value for Shear*Load Duration Factor*Wet Service Factor*Temperature Factor*Shear Stress Factor

Adjusted Design Value for Tension

LaTeX Go Adjusted Design Value = (Design Value for Tension*Load Duration Factor*Wet Service Factor*Temperature Factor*Size Factor)

Adjusted Design Value for Compression Perpendicular to Grain

LaTeX Go Adjusted Design Value = Design Value for Compression Perpendicular*Wet Service Factor*Temperature Factor*Bearing Area Factor

Adjusted Design Value for Compression Perpendicular to Grain Formula

LaTeX Go

Adjusted Design Value = Design Value for Compression Perpendicular*Wet Service Factor*Temperature Factor*Bearing Area Factor
F' = F_c⊥*C_m*C_t*C_b

What is Adjusted Design Value?

Application of the required adjustment is necessary as there is always some variation in the design values calculated in timber.

What is Column Stability Factor?

The column stability factor is to ensure that weak-axis buckling or torsional buckling does not occur over non-laterally supported lengths. Note that this is similar to the beam stability factor except it deals with columns in compression, vs. beams in flexure.

How to Calculate Adjusted Design Value for Compression Perpendicular to Grain?

Adjusted Design Value for Compression Perpendicular to Grain calculator uses Adjusted Design Value = Design Value for Compression Perpendicular*Wet Service Factor*Temperature Factor*Bearing Area Factor to calculate the Adjusted Design Value, The Adjusted Design Value for Compression Perpendicular to Grain formula is defined as correcting the design value by using factors such as wet-service factor, temperature factor and bearing factor. Adjusted Design Value is denoted by F' symbol.

How to calculate Adjusted Design Value for Compression Perpendicular to Grain using this online calculator? To use this online calculator for Adjusted Design Value for Compression Perpendicular to Grain, enter Design Value for Compression Perpendicular (F_c⊥), Wet Service Factor (C_m), Temperature Factor (C_t) & Bearing Area Factor (C_b) and hit the calculate button. Here is how the Adjusted Design Value for Compression Perpendicular to Grain calculation can be explained with given input values -> 5.9E-6 = 9000000*0.81*0.8*1.0075.

FAQ

What is Adjusted Design Value for Compression Perpendicular to Grain?

The Adjusted Design Value for Compression Perpendicular to Grain formula is defined as correcting the design value by using factors such as wet-service factor, temperature factor and bearing factor and is represented as F' = F_c⊥*C_m*C_t*C_b or Adjusted Design Value = Design Value for Compression Perpendicular*Wet Service Factor*Temperature Factor*Bearing Area Factor. Design Value for Compression Perpendicular corrects the design value by using some factor, Wet Service Factor is used to signify wood that will not be used in a dry condition, Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time & Bearing area factor is used to increase design values for concentrated loads on wood perpendicular to the grain.

How to calculate Adjusted Design Value for Compression Perpendicular to Grain?

The Adjusted Design Value for Compression Perpendicular to Grain formula is defined as correcting the design value by using factors such as wet-service factor, temperature factor and bearing factor is calculated using Adjusted Design Value = Design Value for Compression Perpendicular*Wet Service Factor*Temperature Factor*Bearing Area Factor. To calculate Adjusted Design Value for Compression Perpendicular to Grain, you need Design Value for Compression Perpendicular (F_c⊥), Wet Service Factor (C_m), Temperature Factor (C_t) & Bearing Area Factor (C_b). With our tool, you need to enter the respective value for Design Value for Compression Perpendicular, Wet Service Factor, Temperature Factor & Bearing Area Factor and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Adjusted Design Value?

In this formula, Adjusted Design Value uses Design Value for Compression Perpendicular, Wet Service Factor, Temperature Factor & Bearing Area Factor. We can use 3 other way(s) to calculate the same, which is/are as follows -

Adjusted Design Value = (Design Value for Tension*Load Duration Factor*Wet Service Factor*Temperature Factor*Size Factor)
Adjusted Design Value = Design Value for Shear*Load Duration Factor*Wet Service Factor*Temperature Factor*Shear Stress Factor
Adjusted Design Value = (Design Value for Parallel Compression*Load Duration Factor*Wet Service Factor*Temperature Factor*Size Factor*Column Stability Factor)

Home

FREE PDFs

🔍 Search